Co-Form meltblown process: Part III – effect of process parameters on shedding of particles

This study, the third in a series, investigates the effect of processing parameters on the shedding stability of aluminum oxide (AO) particles within co-form meltblown nonwoven webs produced from Pebax® 2533, a polyether block amide elastomer. Building on the loading efficiency and spatial distribution findings of Parts I and II, particle retention was quantified using a Ro-Tap agitation protocol under standardized mechanical stress. Overall shedding was low across all conditions, ranging from 0.15 to 2.43% by mass. Particle size was the primary determinant of retention: 600 μm particles were the most stable (0.3–0.8% loss), while 300 μm particles showed the highest losses (up to 2.4%). Insertion distance produced a counterintuitive, non-monotonic result: shedding was lowest at 15 cm (mean 0.73%), highest at 38 cm (mean 1.28%), and intermediate at 60 cm (mean 0.92%). This behavior is explained by three physically distinct retention mechanisms that operate at different distances from the die. At 15 cm, fibers are still near their crystallization temperature (∼T cryst = 110 °C) due to the 220 °C process air, enabling Frenkel sintering and encapsulation of the particles as the fiber cools and solidifies around them. At 38 cm, fully solidified fibers undergo elastic rebound on contact with the rigid AO particles, forming only a sparse mechanical cage with weak retention—particularly for smaller particles that intercept few fibers. At 60 cm, particles settle into a pre-formed, consolidated fiber mat rather than encountering high-velocity flying fibers, resulting in better passive entrapment than at 38 cm despite an identical fiber thermal state. Air pressure (6–10 psi) had no statistically significant effect on shedding ( p = 0.51), confirming that it does not alter the retention regime, only the web structure. Silane surface treatment of 425 μm particles did not significantly change mean shedding but substantially reduced sample-to-sample variability. These results complete a process–structure–property framework for designing stable, high-performance co-form nonwovens, and establish insertion distance as the primary lever for controlling both particle loading and retention.

Authors

Institutions

Publication Details

Journal
Fibers and Polymers
Published
2026-11-21
DOI
https://doi.org/10.1007/s12221-026-01632-0
Primary Topic
Textile materials and evaluations
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Co-Form meltblown process: Part III – effect of process parameters on shedding of particles

Benoît Mazé, Md Nur Uddin, Behnam Pourdeyhimi
Fibers and Polymers
Textile materials and evaluations
article

Co-Form meltblown process: Part III – effect of process parameters on shedding of particles

Benoît Mazé, Md Nur Uddin, Behnam Pourdeyhimi
article en

Abstract

This study, the third in a series, investigates the effect of processing parameters on the shedding stability of aluminum oxide (AO) particles within co-form meltblown nonwoven webs produced from Pebax® 2533, a polyether block amide elastomer. Building on the loading efficiency and spatial distribution findings of Parts I and II, particle retention was quantified using a Ro-Tap agitation protocol under standardized mechanical stress. Overall shedding was low across all conditions, ranging from 0.15 to 2.43% by mass. Particle size was the primary determinant of retention: 600 μm particles were the most stable (0.3–0.8% loss), while 300 μm particles showed the highest losses (up to 2.4%). Insertion distance produced a counterintuitive, non-monotonic result: shedding was lowest at 15 cm (mean 0.73%), highest at 38 cm (mean 1.28%), and intermediate at 60 cm (mean 0.92%). This behavior is explained by three physically distinct retention mechanisms that operate at different distances from the die. At 15 cm, fibers are still near their crystallization temperature (∼T cryst = 110 °C) due to the 220 °C process air, enabling Frenkel sintering and encapsulation of the particles as the fiber cools and solidifies around them. At 38 cm, fully solidified fibers undergo elastic rebound on contact with the rigid AO particles, forming only a sparse mechanical cage with weak retention—particularly for smaller particles that intercept few fibers. At 60 cm, particles settle into a pre-formed, consolidated fiber mat rather than encountering high-velocity flying fibers, resulting in better passive entrapment than at 38 cm despite an identical fiber thermal state. Air pressure (6–10 psi) had no statistically significant effect on shedding ( p = 0.51), confirming that it does not alter the retention regime, only the web structure. Silane surface treatment of 425 μm particles did not significantly change mean shedding but substantially reduced sample-to-sample variability. These results complete a process–structure–property framework for designing stable, high-performance co-form nonwovens, and establish insertion distance as the primary lever for controlling both particle loading and retention.

Fibers and Polymers
North Carolina State University (US), The Nonwovens Institute (US)
Textile materials and evaluations
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon