Research on the calculation method of flexural bearing capacity of wet joints of prefabricated concrete bridge beams based on the strut and tie model

Wet joints in prefabricated concrete bridge beams constitute typical disturbed regions (D-regions), where geometric change, reinforcement discontinuity, and material heterogeneity invalidate conventional beam theory. This study proposes a two-level analytical framework for UHPC wet joints: the strut-and-tie model (STM) is first used to represent the internal force-transfer mechanism of the joint region, and a sectional equilibrium analysis is then employed to convert the governing tie-strut state into positive-section flexural capacity. To adapt STM to UHPC wet joints, an effective UHPC participation area is defined from the average crack spacing, and a UHPC-oriented effective compressive-strength coefficient is introduced for the concrete strut. For keyed interfaces, an interface tensile-strength reduction coefficient is further proposed to represent the combined influence of interfacial weakening, mechanical interlocking, and local stress concentration. Four-point bending tests were conducted on specimens with rectangular, rhombus, and Chinese “干”-shaped keyways while keeping joint width, lap form, reinforcement arrangement, material class, and loading scheme unchanged. The proposed method reproduced the test and literature database with a mean error of 11% and a standard deviation of 0.13. Within the investigated parameter range, recommended reduction coefficients are 0.45 for rectangular joints, 0.40 for rhombus joints, and 0 for the “干”-shaped joint. The results show that stronger mechanical interlocking shifts the critical crack path away from the interface and promotes a more stable yielding of longitudinal reinforcement. The proposed method is intended for the investigated laboratory-scale UHPC wet joints; direct extrapolation to other keyway geometries, dimensions, reinforcement ratios, or full-scale bridge prototypes requires further calibration and larger-scale validation.

Authors

Publication Details

Journal
Advances in Bridge Engineering
Published
2026-11-22
DOI
https://doi.org/10.1186/s43251-026-00231-6
Primary Topic
Structural Behavior of Reinforced Concrete
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Research on the calculation method of flexural bearing capacity of wet joints of prefabricated concrete bridge beams based on the strut and tie model

Zeyu Ma, 郇久阳, Yushi Yin, Qinhua Yang et al.
Advances in Bridge Engineering
Structural Behavior of Reinforced Concrete
article

Research on the calculation method of flexural bearing capacity of wet joints of prefabricated concrete bridge beams based on the strut and tie model

Zeyu Ma, 郇久阳, Yushi Yin, Qinhua Yang, Zhihui Zhang
article en

Abstract

Wet joints in prefabricated concrete bridge beams constitute typical disturbed regions (D-regions), where geometric change, reinforcement discontinuity, and material heterogeneity invalidate conventional beam theory. This study proposes a two-level analytical framework for UHPC wet joints: the strut-and-tie model (STM) is first used to represent the internal force-transfer mechanism of the joint region, and a sectional equilibrium analysis is then employed to convert the governing tie-strut state into positive-section flexural capacity. To adapt STM to UHPC wet joints, an effective UHPC participation area is defined from the average crack spacing, and a UHPC-oriented effective compressive-strength coefficient is introduced for the concrete strut. For keyed interfaces, an interface tensile-strength reduction coefficient is further proposed to represent the combined influence of interfacial weakening, mechanical interlocking, and local stress concentration. Four-point bending tests were conducted on specimens with rectangular, rhombus, and Chinese “干”-shaped keyways while keeping joint width, lap form, reinforcement arrangement, material class, and loading scheme unchanged. The proposed method reproduced the test and literature database with a mean error of 11% and a standard deviation of 0.13. Within the investigated parameter range, recommended reduction coefficients are 0.45 for rectangular joints, 0.40 for rhombus joints, and 0 for the “干”-shaped joint. The results show that stronger mechanical interlocking shifts the critical crack path away from the interface and promotes a more stable yielding of longitudinal reinforcement. The proposed method is intended for the investigated laboratory-scale UHPC wet joints; direct extrapolation to other keyway geometries, dimensions, reinforcement ratios, or full-scale bridge prototypes requires further calibration and larger-scale validation.

Advances in Bridge EngineeringVol. 7(1)
Structural Behavior of Reinforced Concrete
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon