Consistent interfacial flow numerics - Part II: The momentum convection term

The two-phase Volume-of-Fluid solvers of OpenFOAM overpredict the horizontal water velocity near the crest of a water wave, and the error grows as the wave propagates. Part I of this series removed the spurious air velocities caused by the gravity term but left this error unchanged. Here we show that it is caused by the momentum convection term. Its mass flux is computed in the interface advection step from the velocity at the start of the time step, whereas the convected velocity is taken at the end of the step, because convection is discretised implicitly. In a progressive wave, where the horizontal and vertical velocities are 90 degrees out of phase, this time lag produces an upward flux of horizontal momentum, proportional to the time step, which accumulates in a spurious current near the surface. The same mismatch makes the response to a force depend on the density at the wrong time level. Explicit convection removes the lag and makes the response consistent with the gravity force, but requires the convected face velocity at the interface to be taken from the upwind cell. Only then is the new velocity of a cell a weighted average of old velocities, whatever the density ratio. We demonstrate both requirements with prescribed flows and with the full solver. For a progressive wave, explicit convection with upwind face velocities at the interface reduces the overprediction of the crest velocity from 26-31 % to within 1 % and removes the near-surface current. The resulting solver, fluxinator, is meant for maximum Courant numbers of 0.1 and below, where it keeps the wave height within 1.5 % over 15 periods on meshes with six or more cells per wave height. Because the spurious velocities that limit the time step are removed, it needs 34-42 % less wall-clock time than interFoam for the tested wave.

Authors

Publication Details

Journal
arXiv (Cornell University)
Published
2026-11-18
DOI
https://doi.org/10.48550/arxiv.2611.24866
Primary Topic
Fluid Dynamics and Heat Transfer
Type
preprint
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
preprint

Consistent interfacial flow numerics - Part II: The momentum convection term

Johan Roenby
arXiv (Cornell University)
Fluid Dynamics and Heat Transfer
preprint

Consistent interfacial flow numerics - Part II: The momentum convection term

Johan Roenby
preprint en

Abstract

The two-phase Volume-of-Fluid solvers of OpenFOAM overpredict the horizontal water velocity near the crest of a water wave, and the error grows as the wave propagates. Part I of this series removed the spurious air velocities caused by the gravity term but left this error unchanged. Here we show that it is caused by the momentum convection term. Its mass flux is computed in the interface advection step from the velocity at the start of the time step, whereas the convected velocity is taken at the end of the step, because convection is discretised implicitly. In a progressive wave, where the horizontal and vertical velocities are 90 degrees out of phase, this time lag produces an upward flux of horizontal momentum, proportional to the time step, which accumulates in a spurious current near the surface. The same mismatch makes the response to a force depend on the density at the wrong time level. Explicit convection removes the lag and makes the response consistent with the gravity force, but requires the convected face velocity at the interface to be taken from the upwind cell. Only then is the new velocity of a cell a weighted average of old velocities, whatever the density ratio. We demonstrate both requirements with prescribed flows and with the full solver. For a progressive wave, explicit convection with upwind face velocities at the interface reduces the overprediction of the crest velocity from 26-31 % to within 1 % and removes the near-surface current. The resulting solver, fluxinator, is meant for maximum Courant numbers of 0.1 and below, where it keeps the wave height within 1.5 % over 15 periods on meshes with six or more cells per wave height. Because the spurious velocities that limit the time step are removed, it needs 34-42 % less wall-clock time than interFoam for the tested wave.

arXiv (Cornell University)
Fluid Dynamics and Heat Transfer
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon