Fabrication and Characterization of High-Performance Channel Electron Multipliers Using Alternating Acid and Base Etching and Atomic Layer Deposition

Channel electron multipliers (CEMs) are continuous dynode vacuum electronic devices used in residual gas analysis and mass spectrometry. Owing to the unique structure and intricate fabrication process of CEMs, developing ultra-high-gain, low-noise devices has long been a major engineering challenge worldwide. The CEM was fabricated from lead silicate glass by preform preparation, capillary drawing, inlet flaring, outlet bending, inlet shaping, cleaning, hydrogen reduction, sandblasting isolation, etching, electron-beam evaporation and atomic layer deposition. We characterized the inner-wall morphology and electrical properties following alternating acid and base etching and atomic layer deposition (ALD) using SEM/EDS, AFM, XPS and electrical measurements. Rounded elemental-lead particles (237 ± 31 nm in diameter) were observed on the channel wall after high-temperature hydrogen reduction. Alternating etching with 1.2 mol/L HCl and 8 wt.% NaOH reduced the root-mean-square roughness (Rq) from 1.28 to 0.15 nm. This reduction is hypothesized to result from the dissolution of elemental Pb by HCl and SiO2 by NaOH. At 2.0 kV, pulse gain increased from 2.00 × 106 to 8.25 × 106, while dark count rate decreased from 54.23 to below 2 counts/s. A nominally 5.5 nm Al2O3 coating deposited by ALD further increased gain fourfold to 3.30 × 107. After an accumulated output charge of 0.158 C, analog gain loss decreased from 89% to 11%. Based on CST Studio Suite 2021, a three-dimensional electromagnetic simulation model of CEM was built. The simulation results show that the pulse full width at half maximum (FWHM) of CEM is 6.4 ns, which is basically consistent with the measured result of 8 ns. Increasing protrusion thickness from 0 to 0.4 mm reduced simulated gain from 8.71 × 106 to 2.60 × 106 at 2.0 kV. The combined experimental and simulation results provide a basis for developing CEMs with improved gain, noise performance and lifetime.

Authors

Institutions

Publication Details

Journal
Surfaces
Published
2026-11-19
DOI
https://doi.org/10.3390/surfaces9040097
Primary Topic
Photocathodes and Microchannel Plates
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Fabrication and Characterization of High-Performance Channel Electron Multipliers Using Alternating Acid and Base Etching and Atomic Layer Deposition

鹏杰 牛, Xiaoqing Cong, Shulin Liu, 黎龙辉 LI Longhui et al.
Surfaces
Photocathodes and Microchannel Plates
article

Fabrication and Characterization of High-Performance Channel Electron Multipliers Using Alternating Acid and Base Etching and Atomic Layer Deposition

鹏杰 牛, Xiaoqing Cong, Shulin Liu, 黎龙辉 LI Longhui, 祝佳祺 ZHU Jiaqi, Zexun Hu, Heng Zhao, Yunsheng Qian, Yan Cheng, Jian Wang
article en

Abstract

Channel electron multipliers (CEMs) are continuous dynode vacuum electronic devices used in residual gas analysis and mass spectrometry. Owing to the unique structure and intricate fabrication process of CEMs, developing ultra-high-gain, low-noise devices has long been a major engineering challenge worldwide. The CEM was fabricated from lead silicate glass by preform preparation, capillary drawing, inlet flaring, outlet bending, inlet shaping, cleaning, hydrogen reduction, sandblasting isolation, etching, electron-beam evaporation and atomic layer deposition. We characterized the inner-wall morphology and electrical properties following alternating acid and base etching and atomic layer deposition (ALD) using SEM/EDS, AFM, XPS and electrical measurements. Rounded elemental-lead particles (237 ± 31 nm in diameter) were observed on the channel wall after high-temperature hydrogen reduction. Alternating etching with 1.2 mol/L HCl and 8 wt.% NaOH reduced the root-mean-square roughness (Rq) from 1.28 to 0.15 nm. This reduction is hypothesized to result from the dissolution of elemental Pb by HCl and SiO2 by NaOH. At 2.0 kV, pulse gain increased from 2.00 × 106 to 8.25 × 106, while dark count rate decreased from 54.23 to below 2 counts/s. A nominally 5.5 nm Al2O3 coating deposited by ALD further increased gain fourfold to 3.30 × 107. After an accumulated output charge of 0.158 C, analog gain loss decreased from 89% to 11%. Based on CST Studio Suite 2021, a three-dimensional electromagnetic simulation model of CEM was built. The simulation results show that the pulse full width at half maximum (FWHM) of CEM is 6.4 ns, which is basically consistent with the measured result of 8 ns. Increasing protrusion thickness from 0 to 0.4 mm reduced simulated gain from 8.71 × 106 to 2.60 × 106 at 2.0 kV. The combined experimental and simulation results provide a basis for developing CEMs with improved gain, noise performance and lifetime.

SurfacesVol. 9(4)
Chinese Academy of Sciences (CN), China North Industries Group Corporation (China) (CN), Nanjing University of Science and Technology (CN), Institute of High Energy Physics (CN), Kunming Institute of Physics (CN)
Photocathodes and Microchannel Plates
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon