Microstructure–Tribology Relationship in Ti-6Al-4V Alloy After Short-Duration Low-Pressure Gas Nitriding

Ti-6Al-4V alloy is widely used in aerospace, biomedical, and engineering applications because of its high specific strength, corrosion resistance, and biocompatibility. However, its relatively low surface hardness and poor wear resistance limit its use under sliding-contact conditions. In this study, Ti-6Al-4V specimens were subjected to low-pressure gas nitriding at 950 °C for 60, 100, and 130 min to investigate the effects of short nitriding time on microstructure, hardness, and tribological behavior. The nitrided layers were characterized by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), electron backscatter diffraction (EBSD), and X-ray diffraction (XRD). Cross-sectional microhardness, Rockwell C indentation, surface roughness, and dry sliding wear tests according to ASTM G99 were also evaluated. Low-pressure gas nitriding produced a graded surface region consisting mainly of a TiN/Ti2N compound layer and an α-Ti(N) diffusion zone. Increasing nitriding time promoted nitrogen penetration and development of the nitrided region. The N100 specimen exhibited the highest near-surface microhardness of approximately 550 HV0.025, whereas N130 showed a lower value of approximately 490 HV0.025. Despite its lower near-surface hardness than N100, N130 exhibited the lowest mean wear loss among the nitrided specimens, with a gravimetrically estimated wear volume of 0.722 ± 0.060 mm3 and a specific wear rate of (5.99 ± 0.50) × 10−4 mm3/(N·m). After correction using the adjacent unworn surfaces as references, the maximum wear depths in representative profiles were approximately 49.2, 47.8, and 23.3 μm for N60, N100, and N130, respectively. These depths exceeded the corresponding TiN/Ti2N compound-layer thicknesses of approximately 6–10 μm, indicating local penetration through the outer compound layer in all three conditions during prolonged sliding under a normal load of 4 N. The wear response did not follow the same trend as near-surface hardness, compound-layer thickness, or initial surface roughness, indicating that no single parameter alone governed material removal. Instead, the results suggest that the overall response of the graded nitrided region, including penetration depth, layer integrity, surface condition, and subsurface mechanical support, collectively influenced the tribological behavior. SEM and EDS observations were consistent with abrasive wear features accompanied by local adhesion, tribo-oxidation, delamination, and third-body interactions, although the relative contribution of each mechanism could not be determined conclusively. Under the present test condition, the untreated specimen exhibited the lowest overall wear volume, whereas N130 showed the lowest material loss among the nitrided specimens. The formation of an effective nitrided region within 60–130 min at 950 °C demonstrates the feasibility of short-duration LPGN and suggests potential reductions in processing time and thermal exposure.

Authors

Institutions

Publication Details

Journal
Lubricants
Published
2026-11-19
DOI
https://doi.org/10.3390/lubricants14110443
Primary Topic
Surface Treatment and Coatings
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Microstructure–Tribology Relationship in Ti-6Al-4V Alloy After Short-Duration Low-Pressure Gas Nitriding

Shih‐Hsien Chang, Ching-Quan Tsai, Chih-Hao Yang, Changyu Li
Lubricants
Surface Treatment and Coatings
article

Microstructure–Tribology Relationship in Ti-6Al-4V Alloy After Short-Duration Low-Pressure Gas Nitriding

Shih‐Hsien Chang, Ching-Quan Tsai, Chih-Hao Yang, Changyu Li
article en

Abstract

Ti-6Al-4V alloy is widely used in aerospace, biomedical, and engineering applications because of its high specific strength, corrosion resistance, and biocompatibility. However, its relatively low surface hardness and poor wear resistance limit its use under sliding-contact conditions. In this study, Ti-6Al-4V specimens were subjected to low-pressure gas nitriding at 950 °C for 60, 100, and 130 min to investigate the effects of short nitriding time on microstructure, hardness, and tribological behavior. The nitrided layers were characterized by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), electron backscatter diffraction (EBSD), and X-ray diffraction (XRD). Cross-sectional microhardness, Rockwell C indentation, surface roughness, and dry sliding wear tests according to ASTM G99 were also evaluated. Low-pressure gas nitriding produced a graded surface region consisting mainly of a TiN/Ti2N compound layer and an α-Ti(N) diffusion zone. Increasing nitriding time promoted nitrogen penetration and development of the nitrided region. The N100 specimen exhibited the highest near-surface microhardness of approximately 550 HV0.025, whereas N130 showed a lower value of approximately 490 HV0.025. Despite its lower near-surface hardness than N100, N130 exhibited the lowest mean wear loss among the nitrided specimens, with a gravimetrically estimated wear volume of 0.722 ± 0.060 mm3 and a specific wear rate of (5.99 ± 0.50) × 10−4 mm3/(N·m). After correction using the adjacent unworn surfaces as references, the maximum wear depths in representative profiles were approximately 49.2, 47.8, and 23.3 μm for N60, N100, and N130, respectively. These depths exceeded the corresponding TiN/Ti2N compound-layer thicknesses of approximately 6–10 μm, indicating local penetration through the outer compound layer in all three conditions during prolonged sliding under a normal load of 4 N. The wear response did not follow the same trend as near-surface hardness, compound-layer thickness, or initial surface roughness, indicating that no single parameter alone governed material removal. Instead, the results suggest that the overall response of the graded nitrided region, including penetration depth, layer integrity, surface condition, and subsurface mechanical support, collectively influenced the tribological behavior. SEM and EDS observations were consistent with abrasive wear features accompanied by local adhesion, tribo-oxidation, delamination, and third-body interactions, although the relative contribution of each mechanism could not be determined conclusively. Under the present test condition, the untreated specimen exhibited the lowest overall wear volume, whereas N130 showed the lowest material loss among the nitrided specimens. The formation of an effective nitrided region within 60–130 min at 950 °C demonstrates the feasibility of short-duration LPGN and suggests potential reductions in processing time and thermal exposure.

LubricantsVol. 14(11)
National Taipei University of Technology (TW), National Pingtung University of Science and Technology (TW)
Surface Treatment and Coatings
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon