Research into the method of selective electric-arc additive melting of samples made from powders of austenitic stainless steel AISI 316L

Purpose ‒ to identify the range of permissible values for technological parameters (welding current, inter-electrode gap, and layer thickness) when forming samples from austenitic stainless steel powder AISI 316L, as well as at subsequently studying their microstructure and porosity. Methods. Experimental samples were manufactured on a modernized laboratory bench with CNC and a PROFI TIG 315 P AC/DC welding source in an argon environment. The construction material used was AISI 316L powder with a particle size of 150–350 µm, applied to a substrate made of 03Kh17N14M3 steel. To determine the permissible modes, a visual criterion for assessing the continuity and geometry of the rolls was used. Metallographic analysis and porosity determination were carried out using an Altami MET 1S microscope with Thixomet software using the linear method. The preparation of the sections and etching were carried out using a solution of CuSO4, H2SO4, and HCl. Results. As a result of the research, the technological limitations of the selective electric‑arc additive melting process for samples made of austenitic stainless steel powders have been established: the minimum flow rate of the shielding gas must not be less than 5 L/min, the minimum welding current is 90 A, the minimum layer thickness is 1 mm, and the inter-electrode gap must not exceed 2 mm. Based on the obtained data, the range of permissible mode values has been constructed. Metallographic examination of the sample, showed that the maximum grain size in the structure is 0.39 mm, which corresponds to the level of cast steels, and the porosity does not exceed 0.3%. Conclusion . The range of permissible values for the parameters of the selective electric-arc melting of samples made from powder of austenitic stainless steel AISI 316L has been determined specifically, the deposition current and the layer thickness. The results of metallographic examination show that the sample obtained by selective electric-arc melting of powder has an average grain size typical of steels produced using casting technology, and the porosity does not exceed the maximum porosity established for samples.

Authors

Publication Details

Journal
Proceedings of the Southwest State University Series Engineering and Technologies
Published
2026-11-18
DOI
https://doi.org/10.21869/2223-1528-2026-16-3-52-63
Primary Topic
Additive Manufacturing Materials and Processes
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Research into the method of selective electric-arc additive melting of samples made from powders of austenitic stainless steel AISI 316L

Alexander N. Grechukhin, V. V. Kuts, I. A. Chernyshev, A. V. Oleshitsky
Proceedings of the Southwest State University Series Engineering and Technologies
Additive Manufacturing Materials and Processes
article

Research into the method of selective electric-arc additive melting of samples made from powders of austenitic stainless steel AISI 316L

Alexander N. Grechukhin, V. V. Kuts, I. A. Chernyshev, A. V. Oleshitsky
article en

Abstract

Purpose ‒ to identify the range of permissible values for technological parameters (welding current, inter-electrode gap, and layer thickness) when forming samples from austenitic stainless steel powder AISI 316L, as well as at subsequently studying their microstructure and porosity. Methods. Experimental samples were manufactured on a modernized laboratory bench with CNC and a PROFI TIG 315 P AC/DC welding source in an argon environment. The construction material used was AISI 316L powder with a particle size of 150–350 µm, applied to a substrate made of 03Kh17N14M3 steel. To determine the permissible modes, a visual criterion for assessing the continuity and geometry of the rolls was used. Metallographic analysis and porosity determination were carried out using an Altami MET 1S microscope with Thixomet software using the linear method. The preparation of the sections and etching were carried out using a solution of CuSO4, H2SO4, and HCl. Results. As a result of the research, the technological limitations of the selective electric‑arc additive melting process for samples made of austenitic stainless steel powders have been established: the minimum flow rate of the shielding gas must not be less than 5 L/min, the minimum welding current is 90 A, the minimum layer thickness is 1 mm, and the inter-electrode gap must not exceed 2 mm. Based on the obtained data, the range of permissible mode values has been constructed. Metallographic examination of the sample, showed that the maximum grain size in the structure is 0.39 mm, which corresponds to the level of cast steels, and the porosity does not exceed 0.3%. Conclusion . The range of permissible values for the parameters of the selective electric-arc melting of samples made from powder of austenitic stainless steel AISI 316L has been determined specifically, the deposition current and the layer thickness. The results of metallographic examination show that the sample obtained by selective electric-arc melting of powder has an average grain size typical of steels produced using casting technology, and the porosity does not exceed the maximum porosity established for samples.

Proceedings of the Southwest State University Series Engineering and TechnologiesVol. 16(3)
Additive Manufacturing Materials and Processes
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon