Unified Framework for Hardening Soil Stiffness Parameters G 0 , γ 0.7 , and E 50 from Direct Strain-Measurement Pressuremeter Tests

The design of most geotechnical structures (retaining walls, foundations, tunnels, dams, natural and anthropogenic slopes) relies on finite-element models to predict deformations and performance over time. Advanced numerical analyses utilizing hyperbolic elastoplastic constitutive models are used to represent the measured deformations. As a result, the definition of the complete stiffness degradation curve of a soil or soft rock has taken on increased importance. The hardening soil model with small-strain stiffness (HSS) is gaining widespread use because it offers improved agreement with field measurements and can be implemented with relatively little computational or modeling complexity. The model, however, depends on accurate definition of the small-strain shear modulus ( G 0 ), a reference shear strain ( γ 0.7 ), the unload–reload stiffness ( E u r ), and the secant stiffness at 50% of deviatoric strength ( E 50 ), which are traditionally obtained through laboratory testing. Historically, the G 0 of a soil or soft rock is obtained using either downhole or cross-hole seismic testing. Seismic testing in situ is limited in that it can only provide a single value of the linear-elastic shear modulus, G 0 , for each test interval. Complete nonlinear-elastic behavior must be obtained through advanced laboratory testing using either a resonant column or a triaxial test with local strain sensors. However, this testing is not always possible in heavily overconsolidated soils or soft rocks that do not readily lend themselves to sampling or laboratory testing. The proposed method describes the estimation of G 0 , the reference shear strain γ 0.7 , and a corresponding E 50 from nonlinear field data obtained from pressuremeter unload–reload cycles, normalized to a common reference stress. It will be shown that in situ test data are sufficient to characterize the nonlinear-elastic response and provide the parameters required for most hyperbolic elastoplastic constitutive models. The proposed analysis has been verified using seismic testing (downhole determination of G 0 ) and numerical simulation of a pressuremeter field test.

Authors

Institutions

Publication Details

Journal
Journal of Geotechnical and Geoenvironmental Engineering
Published
2026-11-19
DOI
https://doi.org/10.1061/jggefk.gteng-15508
Primary Topic
Geotechnical Engineering and Soil Mechanics
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Unified Framework for Hardening Soil Stiffness Parameters G 0 , γ 0.7 , and E 50 from Direct Strain-Measurement Pressuremeter Tests

Alexandre Lopes dos Santos, David E. Y. Elwood, Hari Om Sharma, Yasmin Byrne
Journal of Geotechnical and Geoenvironmental Engineering
Geotechnical Engineering and Soil Mechanics
article

Unified Framework for Hardening Soil Stiffness Parameters G 0 , γ 0.7 , and E 50 from Direct Strain-Measurement Pressuremeter Tests

Alexandre Lopes dos Santos, David E. Y. Elwood, Hari Om Sharma, Yasmin Byrne
article en

Abstract

The design of most geotechnical structures (retaining walls, foundations, tunnels, dams, natural and anthropogenic slopes) relies on finite-element models to predict deformations and performance over time. Advanced numerical analyses utilizing hyperbolic elastoplastic constitutive models are used to represent the measured deformations. As a result, the definition of the complete stiffness degradation curve of a soil or soft rock has taken on increased importance. The hardening soil model with small-strain stiffness (HSS) is gaining widespread use because it offers improved agreement with field measurements and can be implemented with relatively little computational or modeling complexity. The model, however, depends on accurate definition of the small-strain shear modulus ( G 0 ), a reference shear strain ( γ 0.7 ), the unload–reload stiffness ( E u r ), and the secant stiffness at 50% of deviatoric strength ( E 50 ), which are traditionally obtained through laboratory testing. Historically, the G 0 of a soil or soft rock is obtained using either downhole or cross-hole seismic testing. Seismic testing in situ is limited in that it can only provide a single value of the linear-elastic shear modulus, G 0 , for each test interval. Complete nonlinear-elastic behavior must be obtained through advanced laboratory testing using either a resonant column or a triaxial test with local strain sensors. However, this testing is not always possible in heavily overconsolidated soils or soft rocks that do not readily lend themselves to sampling or laboratory testing. The proposed method describes the estimation of G 0 , the reference shear strain γ 0.7 , and a corresponding E 50 from nonlinear field data obtained from pressuremeter unload–reload cycles, normalized to a common reference stress. It will be shown that in situ test data are sufficient to characterize the nonlinear-elastic response and provide the parameters required for most hyperbolic elastoplastic constitutive models. The proposed analysis has been verified using seismic testing (downhole determination of G 0 ) and numerical simulation of a pressuremeter field test.

Journal of Geotechnical and Geoenvironmental EngineeringVol. 153(2)
University of Saskatchewan (CA), Setec (France) (FR)
Geotechnical Engineering and Soil Mechanics
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon