A Spot-Scale Orbital Scanning Strategy for Nanosecond Laser Micro-Dimpling of Tungsten Carbide–Cobalt: Energy–Geometry Relationships and Surface Characteristics

Laser micro-dimpling of WC–Co cemented carbides presents considerable challenges due to complex laser–material interactions affecting material removal, geometrical accuracy, and surface morphology. This study investigates a fixed-geometry orbital scanning strategy for fabricating micro-dimples on WC–10 wt.% Co cemented carbide using a 1064 nm nanosecond pulsed fiber laser. A 50 µm laser spot was scanned along a 50 µm-diameter circular trajectory, producing a nominal scanning envelope of 100 µm. Twenty-four experimental conditions were investigated by varying laser power (20 and 40 W), pulse repetition frequency (20 and 30 kHz), scanning speed (10 and 100 mm/s), and number of passes (6, 12, and 24). Four independent micro-dimples were fabricated under each condition, and the resulting features were characterized using optical microscopy, SEM/EDS, 3D profilometry, and ImageJ-based image analysis. Despite maintaining constant optical and scanning geometries, average micro-dimple diameters of approximately 16–91 µm and depths of 7–62 µm were obtained based on measurements from four independently fabricated micro-dimples per processing condition, whereas the two lowest-fluence conditions produced recast surface features without measurable open cavities. Open cavities were observed at 40 W, with circularity values approximately twice those obtained at 20 W, while EDS analysis revealed localized oxygen and cobalt enrichment. At 20 kHz, the 12-pass conditions within a theoretical fluence range of 12.8–64 J/mm2 exhibited high diameter (DS ≈ 0.95–0.96) and depth (DSh ≈ 0.97–0.99) stability. The proposed Geometric Utilization Ratio (GUR, 0–21.9%) and Thermal Deviation Ratio (TDR, 10–235%) indicated that greater open-cavity utilization did not necessarily correspond to a smaller laser-affected region. Logarithmic depth–fluence and saturation-based diameter–fluence regression analyses suggested that cumulative theoretical fluence alone is insufficient to fully describe micro-dimple geometry. These findings highlight the importance of combining geometrical measurements with surface morphology when evaluating processing conditions. Overall, the proposed GUR–TDR framework provides a quantitative basis for assessing micro-dimple formation and supports application-specific micro-dimple design and array spacing on WC–Co surfaces.

Authors

Institutions

Publication Details

Journal
Journal of Manufacturing and Materials Processing
Published
2026-11-19
DOI
https://doi.org/10.3390/jmmp10110522
Primary Topic
Laser Material Processing Techniques
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

A Spot-Scale Orbital Scanning Strategy for Nanosecond Laser Micro-Dimpling of Tungsten Carbide–Cobalt: Energy–Geometry Relationships and Surface Characteristics

Emin Orhun Baştekeli, Adil Yücel, Hacı Abdullah Tasdemir, Buse Ortac Bastekeli
Journal of Manufacturing and Materials Processing
Laser Material Processing Techniques
article

A Spot-Scale Orbital Scanning Strategy for Nanosecond Laser Micro-Dimpling of Tungsten Carbide–Cobalt: Energy–Geometry Relationships and Surface Characteristics

Emin Orhun Baştekeli, Adil Yücel, Hacı Abdullah Tasdemir, Buse Ortac Bastekeli
article en

Abstract

Laser micro-dimpling of WC–Co cemented carbides presents considerable challenges due to complex laser–material interactions affecting material removal, geometrical accuracy, and surface morphology. This study investigates a fixed-geometry orbital scanning strategy for fabricating micro-dimples on WC–10 wt.% Co cemented carbide using a 1064 nm nanosecond pulsed fiber laser. A 50 µm laser spot was scanned along a 50 µm-diameter circular trajectory, producing a nominal scanning envelope of 100 µm. Twenty-four experimental conditions were investigated by varying laser power (20 and 40 W), pulse repetition frequency (20 and 30 kHz), scanning speed (10 and 100 mm/s), and number of passes (6, 12, and 24). Four independent micro-dimples were fabricated under each condition, and the resulting features were characterized using optical microscopy, SEM/EDS, 3D profilometry, and ImageJ-based image analysis. Despite maintaining constant optical and scanning geometries, average micro-dimple diameters of approximately 16–91 µm and depths of 7–62 µm were obtained based on measurements from four independently fabricated micro-dimples per processing condition, whereas the two lowest-fluence conditions produced recast surface features without measurable open cavities. Open cavities were observed at 40 W, with circularity values approximately twice those obtained at 20 W, while EDS analysis revealed localized oxygen and cobalt enrichment. At 20 kHz, the 12-pass conditions within a theoretical fluence range of 12.8–64 J/mm2 exhibited high diameter (DS ≈ 0.95–0.96) and depth (DSh ≈ 0.97–0.99) stability. The proposed Geometric Utilization Ratio (GUR, 0–21.9%) and Thermal Deviation Ratio (TDR, 10–235%) indicated that greater open-cavity utilization did not necessarily correspond to a smaller laser-affected region. Logarithmic depth–fluence and saturation-based diameter–fluence regression analyses suggested that cumulative theoretical fluence alone is insufficient to fully describe micro-dimple geometry. These findings highlight the importance of combining geometrical measurements with surface morphology when evaluating processing conditions. Overall, the proposed GUR–TDR framework provides a quantitative basis for assessing micro-dimple formation and supports application-specific micro-dimple design and array spacing on WC–Co surfaces.

Journal of Manufacturing and Materials ProcessingVol. 10(11)
Istanbul Technical University (TR)
Laser Material Processing Techniques
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon