Deposition of Inconel 718 and Stellite 6 Coatings on Steel by Directed Energy Deposition and Evaluation of Cavitation Response under Ultrasonic Testing

Two coatings deposited on steel by directed energy deposition (DED) were exposed to ultrasonic cavitation under a single laboratory protocol. The Inconel 718 coating was deposited on an InssTek MX-Mini system using a laser power of 230 W, a travel speed of 550 mm/min, a 0.15 mm layer height, a 0.30 mm step-over and a powder feed rate of 1.0 g/min; a second series was deposited by the same process route from Stellite 6, a cobalt-based Co-Cr-W-C hardfacing alloy. Both series used the same plain-carbon steel substrate and the same cylindrical specimen geometry. Cylindrical specimens were exposed in distilled water on a piezoceramic vibratory apparatus at a frequency of 20 ± 0.03 kHz, a vibration amplitude of 50 µm and a water temperature of 22 ± 1 °C, for a total attack time of 165 min. For the Stellite 6 series, cumulative mass loss was recorded gravimetrically at eight intermediate intervals and described by with A = 0.12, B = 3.873 × 10⁻³ and an endpoint cumulative mass loss of 9.35 mg. The Inconel 718 series was characterized after exposure by optical observation, scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS). The eroded Inconel 718 surface showed a radial, flow-like morphology together with localized pits and shallow grooves, without macroscopic coating detachment in the examined fields. A representative EDS acquisition yielded 41.5 wt% Ni, 19.3 wt% Cr and 39.2 wt% Fe, normalized over three elements. The Ni-Cr signal confirms that the deposited layer was retained at the analyzed location, while the Fe level, more than twice the nominal content of Inconel 718, corresponds to a substrate dilution of the order of 20-25 % under a simple two-source mixing assumption. Deposition route, machine, substrate, specimen geometry and test conditions were common to the two series, although the Stellite 6 deposition ran under closed-loop laser-power control while the Inconel 718 parameters are reported at a fixed setting; the Stellite 6 data quantify the erosion kinetics of that common exposure, while the Inconel 718 data document damage morphology and near-surface chemistry. No quantitative resistance ranking between the two coatings is claimed, because gravimetric records were acquired only for the Stellite 6 series.

Authors

Institutions

Publication Details

Journal
Diffusion and defect data, solid state data. Part B, Solid state phenomena/Solid state phenomena
Published
2026-11-18
DOI
https://doi.org/10.4028/p-z9fcc1
Primary Topic
Additive Manufacturing Materials and Processes
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Deposition of Inconel 718 and Stellite 6 Coatings on Steel by Directed Energy Deposition and Evaluation of Cavitation Response under Ultrasonic Testing

Ilare Bordeașu, Nicuşor Alin Sîrbu, Denis Andrei Predu, Raluca Faur et al.
Diffusion and defect data, solid state data. Part B, Solid state phenomena/Solid state phenomena
Additive Manufacturing Materials and Processes
article

Deposition of Inconel 718 and Stellite 6 Coatings on Steel by Directed Energy Deposition and Evaluation of Cavitation Response under Ultrasonic Testing

Ilare Bordeașu, Nicuşor Alin Sîrbu, Denis Andrei Predu, Raluca Faur, Doru Alexandru Luca
article en

Abstract

Two coatings deposited on steel by directed energy deposition (DED) were exposed to ultrasonic cavitation under a single laboratory protocol. The Inconel 718 coating was deposited on an InssTek MX-Mini system using a laser power of 230 W, a travel speed of 550 mm/min, a 0.15 mm layer height, a 0.30 mm step-over and a powder feed rate of 1.0 g/min; a second series was deposited by the same process route from Stellite 6, a cobalt-based Co-Cr-W-C hardfacing alloy. Both series used the same plain-carbon steel substrate and the same cylindrical specimen geometry. Cylindrical specimens were exposed in distilled water on a piezoceramic vibratory apparatus at a frequency of 20 ± 0.03 kHz, a vibration amplitude of 50 µm and a water temperature of 22 ± 1 °C, for a total attack time of 165 min. For the Stellite 6 series, cumulative mass loss was recorded gravimetrically at eight intermediate intervals and described by with A = 0.12, B = 3.873 × 10⁻³ and an endpoint cumulative mass loss of 9.35 mg. The Inconel 718 series was characterized after exposure by optical observation, scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS). The eroded Inconel 718 surface showed a radial, flow-like morphology together with localized pits and shallow grooves, without macroscopic coating detachment in the examined fields. A representative EDS acquisition yielded 41.5 wt% Ni, 19.3 wt% Cr and 39.2 wt% Fe, normalized over three elements. The Ni-Cr signal confirms that the deposited layer was retained at the analyzed location, while the Fe level, more than twice the nominal content of Inconel 718, corresponds to a substrate dilution of the order of 20-25 % under a simple two-source mixing assumption. Deposition route, machine, substrate, specimen geometry and test conditions were common to the two series, although the Stellite 6 deposition ran under closed-loop laser-power control while the Inconel 718 parameters are reported at a fixed setting; the Stellite 6 data quantify the erosion kinetics of that common exposure, while the Inconel 718 data document damage morphology and near-surface chemistry. No quantitative resistance ranking between the two coatings is claimed, because gravimetric records were acquired only for the Stellite 6 series.

Diffusion and defect data, solid state data. Part B, Solid state phenomena/Solid state phenomenaVol. 396
Polytechnic University of Timişoara (RO)
Additive Manufacturing Materials and Processes
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon