EEZYBOT MK1 ROBOTIC MANIPULATOR ARM

Small robotic arms are widely used in education and in light automation to demonstrate how mechanisms, actuators, sensors and control software work together. The EEZYbot MK1 is an open-source, 3D-printable desktop manipulator designed by daGHIZmo in the form of a compact palletising arm. It has three degrees of freedom, a rotating base, a main arm and a forearm, and uses a parallel four-bar linkage so that the forearm and gripper keep their orientation while the arm moves. This project builds and studies the EEZYbot MK1 as a low-cost manipulator for pick-and-place tasks and examines its kinematics, structural strength and positioning performance. The arm was assembled from the published part geometry, which was checked and adapted in SolidWorks, and the parts were printed in PLA on a fused deposition printer with a 0.2 mm layer height and 30 percent infill. Three MG995 servos drive the base, the main arm and the forearm, and an MG90S micro servo operates the claw gripper. An Arduino Uno generates the motion commands and sends them to a PCA9685 16-channel servo driver powered by a separate 5 V, 5 A supply. A serial command interface allows a target point in Cartesian coordinates to be entered from a computer, and the controller converts it into joint angles. Forward and inverse kinematics were derived for the arm. Because the four-bar linkage references the forearm angle to the base, the shoulder servo sets the absolute angle of the main arm and the elbow servo sets the absolute angle of the forearm, which simplifies the inverse solution to a planar two-link problem combined with base rotation. With link lengths of 135 mm and 147 mm the computed workspace extends from 75 mm to 245 mm in horizontal reach and from minus 40 mm to 210 mm in height relative to the base plate over a base rotation of 180 degrees. Static finite element analysis of the printed main arm and forearm in ANSYS gave a maximum von Mises stress of 14.8 MPa under the rated payload with a dynamic factor of 2, a factor of safety of 3.4. The assembled arm was tested in pick-and-place trials with small blocks moved between marked positions on a grid. Over 30 repeated cycles to the same point, the repeatability measured with a dial gauge was within plus or minus 1.2 mm. The mean positioning error over 20 grid points fell from 7.9 mm to 3.6 mm after servo offset calibration. The arm handled a rated payload of 150 g, completed 47 out of 50 pickand-place trials successfully, a success rate of 94 percent, and took an average of 6.8 seconds per cycle.

Authors

Publication Details

Journal
International Journal of AI Electrical Civil and Mechanical engineering
Published
2026-11-17
DOI
https://doi.org/10.64751/3nsedj40
Primary Topic
Robotic Mechanisms and Dynamics
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

EEZYBOT MK1 ROBOTIC MANIPULATOR ARM

B. Santhosh Kumar, T.Shashidar, K.Sneha, K.Pramod Kumar, J.Vikas
International Journal of AI Electrical Civil and Mechanical engineering
Robotic Mechanisms and Dynamics
article

EEZYBOT MK1 ROBOTIC MANIPULATOR ARM

B. Santhosh Kumar, T.Shashidar, K.Sneha, K.Pramod Kumar, J.Vikas
article en

Abstract

Small robotic arms are widely used in education and in light automation to demonstrate how mechanisms, actuators, sensors and control software work together. The EEZYbot MK1 is an open-source, 3D-printable desktop manipulator designed by daGHIZmo in the form of a compact palletising arm. It has three degrees of freedom, a rotating base, a main arm and a forearm, and uses a parallel four-bar linkage so that the forearm and gripper keep their orientation while the arm moves. This project builds and studies the EEZYbot MK1 as a low-cost manipulator for pick-and-place tasks and examines its kinematics, structural strength and positioning performance. The arm was assembled from the published part geometry, which was checked and adapted in SolidWorks, and the parts were printed in PLA on a fused deposition printer with a 0.2 mm layer height and 30 percent infill. Three MG995 servos drive the base, the main arm and the forearm, and an MG90S micro servo operates the claw gripper. An Arduino Uno generates the motion commands and sends them to a PCA9685 16-channel servo driver powered by a separate 5 V, 5 A supply. A serial command interface allows a target point in Cartesian coordinates to be entered from a computer, and the controller converts it into joint angles. Forward and inverse kinematics were derived for the arm. Because the four-bar linkage references the forearm angle to the base, the shoulder servo sets the absolute angle of the main arm and the elbow servo sets the absolute angle of the forearm, which simplifies the inverse solution to a planar two-link problem combined with base rotation. With link lengths of 135 mm and 147 mm the computed workspace extends from 75 mm to 245 mm in horizontal reach and from minus 40 mm to 210 mm in height relative to the base plate over a base rotation of 180 degrees. Static finite element analysis of the printed main arm and forearm in ANSYS gave a maximum von Mises stress of 14.8 MPa under the rated payload with a dynamic factor of 2, a factor of safety of 3.4. The assembled arm was tested in pick-and-place trials with small blocks moved between marked positions on a grid. Over 30 repeated cycles to the same point, the repeatability measured with a dial gauge was within plus or minus 1.2 mm. The mean positioning error over 20 grid points fell from 7.9 mm to 3.6 mm after servo offset calibration. The arm handled a rated payload of 150 g, completed 47 out of 50 pickand-place trials successfully, a success rate of 94 percent, and took an average of 6.8 seconds per cycle.

International Journal of AI Electrical Civil and Mechanical engineering
Robotic Mechanisms and Dynamics
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon