Tangential gas injection-enhanced fuel elements for centrifugal nuclear thermal rockets: A thermal-hydraulic analysis

This study proposes the application of tangential hydrogen injection as an alternative swirl-generation concept for centrifugal nuclear thermal rocket (CNTR) fuel elements and numerically evaluates its gas-side thermal-hydraulic performance. Two swirl-generation mechanisms are investigated: tangential inlet-induced (TII) swirl, produced by tangential hydrogen injection, and wall rotation-induced (WRI) swirl, produced by mechanically rotating boundaries. A two-dimensional axisymmetric-swirl unsteady Reynolds-averaged Navier–Stokes (URANS) framework with Reynolds Stress Model (RSM) turbulence closure was validated against experimental swirling-flow data and subsequently applied to compare the two configurations under matched swirl intensity, inlet mass flow rate, geometry, and thermal boundary conditions. The results show fundamentally different radial swirl distributions: TII produces a Rankine-vortex-type flow with swirl concentrated toward the core and decaying downstream, whereas WRI maintains a forced-vortex-type flow with strong near-wall tangential motion. At the baseline condition of 200 RPM-equivalent swirl and a wall heat flux of 3000 W/m 2 , TII increases the global Nusselt number from 10.63 to 12.66, corresponding to an approximately 19% enhancement over WRI, while producing nearly identical pressure loss. Increasing the imposed swirl from 100 to 600 RPM-equivalent increases the global Nusselt number of TII from 11.50 to 16.48, whereas that of WRI remains nearly unchanged. The resulting Figure of Merit (FoM) for TII increases from approximately 1.06 to 1.63. The radial pressure differences generated by TII and WRI are comparable near the injection region, indicating that both mechanisms generate centrifugal fields that may contribute to fuel retention; however, the TII-induced field decays downstream while the WRI field is continuously sustained by wall rotation. Overall, the results demonstrate the potential of TII for enhancing gas-side heat transfer while generating a centrifugal field and potentially reducing reliance on mechanically rotating components in CNTR fuel elements. Further, two-phase simulations, injector-geometry and outlet-orifice optimization, and system-level analyses are required to determine its feasibility under representative CNTR operating conditions.

Authors

Institutions

Publication Details

Journal
Progress in Nuclear Energy
Published
2026-11-18
DOI
https://doi.org/10.1016/j.pnucene.2026.106697
Primary Topic
Heat transfer and supercritical fluids
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Tangential gas injection-enhanced fuel elements for centrifugal nuclear thermal rockets: A thermal-hydraulic analysis

Qingqing Liu, Kunal Sachdeva
3 links
Progress in Nuclear Energy
Heat transfer and supercritical fluids
article

Tangential gas injection-enhanced fuel elements for centrifugal nuclear thermal rockets: A thermal-hydraulic analysis

Qingqing Liu, Kunal Sachdeva
article en

Abstract

This study proposes the application of tangential hydrogen injection as an alternative swirl-generation concept for centrifugal nuclear thermal rocket (CNTR) fuel elements and numerically evaluates its gas-side thermal-hydraulic performance. Two swirl-generation mechanisms are investigated: tangential inlet-induced (TII) swirl, produced by tangential hydrogen injection, and wall rotation-induced (WRI) swirl, produced by mechanically rotating boundaries. A two-dimensional axisymmetric-swirl unsteady Reynolds-averaged Navier–Stokes (URANS) framework with Reynolds Stress Model (RSM) turbulence closure was validated against experimental swirling-flow data and subsequently applied to compare the two configurations under matched swirl intensity, inlet mass flow rate, geometry, and thermal boundary conditions. The results show fundamentally different radial swirl distributions: TII produces a Rankine-vortex-type flow with swirl concentrated toward the core and decaying downstream, whereas WRI maintains a forced-vortex-type flow with strong near-wall tangential motion. At the baseline condition of 200 RPM-equivalent swirl and a wall heat flux of 3000 W/m 2 , TII increases the global Nusselt number from 10.63 to 12.66, corresponding to an approximately 19% enhancement over WRI, while producing nearly identical pressure loss. Increasing the imposed swirl from 100 to 600 RPM-equivalent increases the global Nusselt number of TII from 11.50 to 16.48, whereas that of WRI remains nearly unchanged. The resulting Figure of Merit (FoM) for TII increases from approximately 1.06 to 1.63. The radial pressure differences generated by TII and WRI are comparable near the injection region, indicating that both mechanisms generate centrifugal fields that may contribute to fuel retention; however, the TII-induced field decays downstream while the WRI field is continuously sustained by wall rotation. Overall, the results demonstrate the potential of TII for enhancing gas-side heat transfer while generating a centrifugal field and potentially reducing reliance on mechanically rotating components in CNTR fuel elements. Further, two-phase simulations, injector-geometry and outlet-orifice optimization, and system-level analyses are required to determine its feasibility under representative CNTR operating conditions.

Progress in Nuclear EnergyVol. 203
Mississippi State University (US)
Affordable and clean energy
Heat transfer and supercritical fluids
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon