IOT BASED SMART ENERGY MANAGEMENT AND ELECTRICAL FAULT DETECTION SYSTEM

Electrical energy is used wastefully in many homes, hostels, small workshops, and commercial buildings because consumers see their consumption only once a month through the utility bill. At the same time, faults such as overloads, short circuits, earth leakage, over-voltage, and under-voltage are usually handled only by fuses and miniature circuit breakers that act after the damage has started and give no information about what went wrong. This paper presents an IoT Based Smart Energy Management and Electrical Fault Detection System that measures consumption continuously, identifies abnormal electrical conditions, isolates the affected load, and reports the event to the user in real time. The system is built around an ESP32 microcontroller connected to a ZMPT101B voltage sensor and ACS712 current sensors on each monitored branch circuit. From the sampled waveforms the controller computes RMS voltage, RMS current, real power, apparent power, power factor, and cumulative energy in kilowatt-hours. A DS18B20 temperature sensor placed near the distribution board detects overheating of terminals, and a core-balance current transformer measures the residual current that indicates earth leakage. Each branch is switched through a relay module so that a faulty or unnecessary load can be disconnected automatically or from the mobile application. Fault detection is carried out on the controller by comparing the computed quantities with protection thresholds and time delays. Over-voltage and under-voltage are judged against limits around the nominal 230 V supply, overload is judged by an inverse time characteristic similar to a thermal relay, short circuit is recognised from a very sharp rise in current within a few cycles, and earth fault is identified from residual current above 30 mA. When a fault is confirmed the relay trips, a buzzer sounds, the cause is shown on an LCD, and a notification is pushed to the user through the cloud.

Authors

Publication Details

Journal
International Journal of AI Electrical Civil and Mechanical engineering
Published
2026-11-17
DOI
https://doi.org/10.64751/8md65w19
Primary Topic
Arduino and IoT Applications
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

IOT BASED SMART ENERGY MANAGEMENT AND ELECTRICAL FAULT DETECTION SYSTEM

Sriramula Srimatha, K. Sree Lakshmi, V. Vinitha, A.Balu Kumar et al.
International Journal of AI Electrical Civil and Mechanical engineering
Arduino and IoT Applications
article

IOT BASED SMART ENERGY MANAGEMENT AND ELECTRICAL FAULT DETECTION SYSTEM

Sriramula Srimatha, K. Sree Lakshmi, V. Vinitha, A.Balu Kumar, T. Shasidhar
article en

Abstract

Electrical energy is used wastefully in many homes, hostels, small workshops, and commercial buildings because consumers see their consumption only once a month through the utility bill. At the same time, faults such as overloads, short circuits, earth leakage, over-voltage, and under-voltage are usually handled only by fuses and miniature circuit breakers that act after the damage has started and give no information about what went wrong. This paper presents an IoT Based Smart Energy Management and Electrical Fault Detection System that measures consumption continuously, identifies abnormal electrical conditions, isolates the affected load, and reports the event to the user in real time. The system is built around an ESP32 microcontroller connected to a ZMPT101B voltage sensor and ACS712 current sensors on each monitored branch circuit. From the sampled waveforms the controller computes RMS voltage, RMS current, real power, apparent power, power factor, and cumulative energy in kilowatt-hours. A DS18B20 temperature sensor placed near the distribution board detects overheating of terminals, and a core-balance current transformer measures the residual current that indicates earth leakage. Each branch is switched through a relay module so that a faulty or unnecessary load can be disconnected automatically or from the mobile application. Fault detection is carried out on the controller by comparing the computed quantities with protection thresholds and time delays. Over-voltage and under-voltage are judged against limits around the nominal 230 V supply, overload is judged by an inverse time characteristic similar to a thermal relay, short circuit is recognised from a very sharp rise in current within a few cycles, and earth fault is identified from residual current above 30 mA. When a fault is confirmed the relay trips, a buzzer sounds, the cause is shown on an LCD, and a notification is pushed to the user through the cloud.

International Journal of AI Electrical Civil and Mechanical engineering
Arduino and IoT Applications
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon