AUTOMOTIVE CONNECTING ROD

The connecting rod links the piston to the crankshaft and converts the reciprocating motion of the piston into the rotary motion of the crank. In every engine cycle it is compressed by the gas force during combustion and pulled in tension by the inertia of the piston assembly near the top of the exhaust stroke, so it works under a fully alternating load at high frequency. A connecting rod failure usually destroys the engine block and crankshaft, and therefore the rod must be strong, stiff against buckling and resistant to fatigue. Because it is a reciprocating part, its mass also directly affects the inertia forces, the bearing loads and the balance of the engine. This paper presents the design and finite element analysis of a connecting rod for a single-cylinder four-stroke petrol engine of 150 cc displacement with a bore of 57 mm and a stroke of 58.6 mm. The rod was sized by the standard I-section design procedure and modelled in SolidWorks with a centre distance of 112 mm. The model was analysed in ANSYS Workbench for a compressive gas load of 8.93 kN, corresponding to a peak cylinder pressure of 3.5 MPa, and a tensile inertia load of 4.2 kN at a maximum speed of 9,000 rpm. Static structural, linear buckling, modal and fatigue analyses were carried out. Four materials were compared using the same geometry, mesh and loads: structural steel, forged alloy steel AISI 4340, aluminium alloy 7075-T6 and titanium alloy Ti6Al-4V. Under the compressive load the maximum von Mises stress was between 166.4 and 168.9 MPa for all materials and occurred at the junction of the shank and the small end. The factor of safety on yield was 1.49 for structural steel, 4.20 for AISI 4340, 3.02 for aluminium 7075-T6 and 5.25 for Ti-6Al-4V. The fatigue analysis showed that structural steel and aluminium 7075-T6 could not reach the target life of one million cycles under the alternating load, while AISI 4340 and Ti-6Al-4V could. Considering strength, fatigue life, buckling margin, manufacturability and cost, forged AISI 4340 was selected, and its I-section was then refined by thinning the web from 4.0 mm to 3.2 mm and tapering the flanges towards the small end. The refined rod has a mass of 0.282 kg against 0.312 kg for the original section, a reduction of 9.6 percent, with a maximum stress of 186.4 MPa, a factor of safety of 3.81, a buckling load factor of 24.1 and a fatigue safety factor of 1.68. Its first natural frequency is well above the crankshaft speed and its second harmonic. The work demonstrates that a computer-aided design and finite element approach can identify the critical regions of a connecting rod, compare candidate materials on a common basis and guide a weight reduction without compromising safety. The approach shortens the design cycle compared with repeated prototype forging and fatigue testing, and it provides a clear record of the reasoning behind the final material and section choice.

Authors

Publication Details

Journal
International Journal of AI Electrical Civil and Mechanical engineering
Published
2026-11-17
DOI
https://doi.org/10.64751/aqxst293
Primary Topic
Mechanical Failure Analysis and Simulation
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

AUTOMOTIVE CONNECTING ROD

Mrs. A. Sandhya, N.Sindhu, G.Arun, V.Abhilash, M.Chandu
International Journal of AI Electrical Civil and Mechanical engineering
Mechanical Failure Analysis and Simulation
article

AUTOMOTIVE CONNECTING ROD

Mrs. A. Sandhya, N.Sindhu, G.Arun, V.Abhilash, M.Chandu
article en

Abstract

The connecting rod links the piston to the crankshaft and converts the reciprocating motion of the piston into the rotary motion of the crank. In every engine cycle it is compressed by the gas force during combustion and pulled in tension by the inertia of the piston assembly near the top of the exhaust stroke, so it works under a fully alternating load at high frequency. A connecting rod failure usually destroys the engine block and crankshaft, and therefore the rod must be strong, stiff against buckling and resistant to fatigue. Because it is a reciprocating part, its mass also directly affects the inertia forces, the bearing loads and the balance of the engine. This paper presents the design and finite element analysis of a connecting rod for a single-cylinder four-stroke petrol engine of 150 cc displacement with a bore of 57 mm and a stroke of 58.6 mm. The rod was sized by the standard I-section design procedure and modelled in SolidWorks with a centre distance of 112 mm. The model was analysed in ANSYS Workbench for a compressive gas load of 8.93 kN, corresponding to a peak cylinder pressure of 3.5 MPa, and a tensile inertia load of 4.2 kN at a maximum speed of 9,000 rpm. Static structural, linear buckling, modal and fatigue analyses were carried out. Four materials were compared using the same geometry, mesh and loads: structural steel, forged alloy steel AISI 4340, aluminium alloy 7075-T6 and titanium alloy Ti6Al-4V. Under the compressive load the maximum von Mises stress was between 166.4 and 168.9 MPa for all materials and occurred at the junction of the shank and the small end. The factor of safety on yield was 1.49 for structural steel, 4.20 for AISI 4340, 3.02 for aluminium 7075-T6 and 5.25 for Ti-6Al-4V. The fatigue analysis showed that structural steel and aluminium 7075-T6 could not reach the target life of one million cycles under the alternating load, while AISI 4340 and Ti-6Al-4V could. Considering strength, fatigue life, buckling margin, manufacturability and cost, forged AISI 4340 was selected, and its I-section was then refined by thinning the web from 4.0 mm to 3.2 mm and tapering the flanges towards the small end. The refined rod has a mass of 0.282 kg against 0.312 kg for the original section, a reduction of 9.6 percent, with a maximum stress of 186.4 MPa, a factor of safety of 3.81, a buckling load factor of 24.1 and a fatigue safety factor of 1.68. Its first natural frequency is well above the crankshaft speed and its second harmonic. The work demonstrates that a computer-aided design and finite element approach can identify the critical regions of a connecting rod, compare candidate materials on a common basis and guide a weight reduction without compromising safety. The approach shortens the design cycle compared with repeated prototype forging and fatigue testing, and it provides a clear record of the reasoning behind the final material and section choice.

International Journal of AI Electrical Civil and Mechanical engineering
Mechanical Failure Analysis and Simulation
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon