A study on porosity formation in cold-spray additively manufactured 6061 aluminium parts using MIG, TIG and FSW welding processes

Cold Spray Additive Manufacturing (CSAM) is a solid-state additive manufacturing process that enables components to be produced and repaired without melting the deposited material. However, limited research has examined the weldability of CSAM components. This study investigates porosity formation and local hardness responses in CSAM 6061 aluminium joined using Tungsten Inert Gas (TIG), Metal Inert Gas (MIG), and Friction Stir Welding (FSW), considering both non-heat-treated (NHT) and heat-treated (HT) conditions. Macroscopic, micrographic, ImageJ-based porosity analysis and Vickers hardness measurements were used to characterise the welded regions. TIG and MIG produced substantial fusion zone porosity with characteristics consistent with hydrogen-assisted pore formation during melting and solidification. Pre-weld heat treatment reduced the measured two-dimensional pore area fraction from 26.3% to 18.6% for TIG and from 30.7% to 22.1% for MIG, while also altering pore size and spatial distribution. TIG exhibited relatively large, interconnected pores extending from the fusion boundary, whereas MIG showed a greater population of smaller pores concentrated towards the upper weld region. Both fusion processes produced local hardness reductions, with hardness recovery of approximately 50–56% for TIG and 63–67% for MIG relative to the corresponding control regions. In contrast, FSW exhibited substantially less macro-porosity, predominantly finer residual microporosity, and hardness recovery of approximately 82–84%. Overall, under the conditions investigated, FSW exhibited lower macro-porosity and more localised hardness reduction than TIG and MIG, while pre-weld heat treatment improved the porosity characteristics of both fusion welding processes.

Authors

Institutions

Publication Details

Journal
The International Journal of Advanced Manufacturing Technology
Published
2026-11-18
DOI
https://doi.org/10.1007/s00170-026-19537-w
Primary Topic
Additive Manufacturing Materials and Processes
Type
article
Field-Weighted Citation Impact
0.00

Funders

Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

A study on porosity formation in cold-spray additively manufactured 6061 aluminium parts using MIG, TIG and FSW welding processes

Aravinthan Arumugam, Krishnan Kannoorpatti, Ryan Riedel
2 links
The International Journal of Advanced Manufacturing Technology
Additive Manufacturing Materials and Processes
article

A study on porosity formation in cold-spray additively manufactured 6061 aluminium parts using MIG, TIG and FSW welding processes

Aravinthan Arumugam, Krishnan Kannoorpatti, Ryan Riedel
article en

Abstract

Cold Spray Additive Manufacturing (CSAM) is a solid-state additive manufacturing process that enables components to be produced and repaired without melting the deposited material. However, limited research has examined the weldability of CSAM components. This study investigates porosity formation and local hardness responses in CSAM 6061 aluminium joined using Tungsten Inert Gas (TIG), Metal Inert Gas (MIG), and Friction Stir Welding (FSW), considering both non-heat-treated (NHT) and heat-treated (HT) conditions. Macroscopic, micrographic, ImageJ-based porosity analysis and Vickers hardness measurements were used to characterise the welded regions. TIG and MIG produced substantial fusion zone porosity with characteristics consistent with hydrogen-assisted pore formation during melting and solidification. Pre-weld heat treatment reduced the measured two-dimensional pore area fraction from 26.3% to 18.6% for TIG and from 30.7% to 22.1% for MIG, while also altering pore size and spatial distribution. TIG exhibited relatively large, interconnected pores extending from the fusion boundary, whereas MIG showed a greater population of smaller pores concentrated towards the upper weld region. Both fusion processes produced local hardness reductions, with hardness recovery of approximately 50–56% for TIG and 63–67% for MIG relative to the corresponding control regions. In contrast, FSW exhibited substantially less macro-porosity, predominantly finer residual microporosity, and hardness recovery of approximately 82–84%. Overall, under the conditions investigated, FSW exhibited lower macro-porosity and more localised hardness reduction than TIG and MIG, while pre-weld heat treatment improved the porosity characteristics of both fusion welding processes.

The International Journal of Advanced Manufacturing Technology
Charles Darwin University (AU), Department of the Premier and Cabinet (AU)
Charles Darwin University
Additive Manufacturing Materials and Processes
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon