Biomechanical Evaluation of Crossed Screw Fixations With Different Head Designs for First Tarsometatarsal Joint Arthrodesis

BackgroundMidfoot arthrodesis is used to treat deformity, instability, and degenerative conditions. Headless compression screws may reduce hardware prominence and soft tissue irritation. We compared the biomechanical properties of conventional and headless compression screws in a modified Lapidus first tarsometatarsal joint (TMTJ) arthrodesis model.MethodsTen matched human lower extremity pairs were randomly assigned to first TMTJ arthrodesis using either 2 crossed headed 4.0-mm cannulated compression screws (HS) or two 4.0-mm cannulated headless compression screws (HLS). After bone mineral density (BMD) assessment, specimens were cyclically loaded from 0 to 31 N for 1000 cycles. Dorsal angulation and construct stiffness were measured during cyclic loading and subsequent loading to failure.ResultsMean stiffness during ultimate load testing was 58.91 ± 31.33 N/mm for headed screws and 68.36 ± 84.29 N/mm for headless screws (P = .842). Mean yield load was 115.80 ± 61.94 and 67.79 ± 35.90 N (P = .101), and mean ultimate load was 142.10 ± 65.24 and 83.02 ± 60.77 N (P = 0.064), respectively. No significant difference in dorsal angulation was observed. Mean BMD was 0.547 ± 0.222 g/cm² for headed screws and 0.533 ± 0.204 g/cm² for headless screws (P = 0.897). Bone mineral density positively correlated with construct stiffness in the headless screw group during several loading cycles, but not in the headed screw group. No significant correlations were found between BMD and yield or ultimate load.ConclusionHeaded and headless crossed screw constructs showed no statistically significant differences in stiffness, yield load, ultimate load, or dorsal angulation. However, the numerical difference in ultimate load favored headed screws. Headless compression screws may offer clinical advantages through their low-profile design, but further biomechanical and clinical studies are warranted.Clinical Relevance:Headless and headed screws showed no statistically significant differences in this cadaveric first tarsometatarsal joint model, although headed screws achieved higher mean failure loads. Their low-profile design may reduce hardware prominence and soft tissue irritation while maintaining adequate primary fixation stability.

Authors

Institutions

Publication Details

Journal
Foot & Ankle Specialist
Published
2026-11-18
DOI
https://doi.org/10.1177/19386400261499833
Primary Topic
Foot and Ankle Surgery
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Biomechanical Evaluation of Crossed Screw Fixations With Different Head Designs for First Tarsometatarsal Joint Arthrodesis

Reinhard Windhager, Madeleine Willegger, Reinhard Schuh, Andrea Veljkovic et al.
1 links
Foot & Ankle Specialist
Foot and Ankle Surgery
article

Biomechanical Evaluation of Crossed Screw Fixations With Different Head Designs for First Tarsometatarsal Joint Arthrodesis

Reinhard Windhager, Madeleine Willegger, Reinhard Schuh, Andrea Veljkovic, Lena Hirtler, Emir Benca, Shahin Zandieh, Joachim Ortmayr, Tamás Dornyi
article en

Abstract

BackgroundMidfoot arthrodesis is used to treat deformity, instability, and degenerative conditions. Headless compression screws may reduce hardware prominence and soft tissue irritation. We compared the biomechanical properties of conventional and headless compression screws in a modified Lapidus first tarsometatarsal joint (TMTJ) arthrodesis model.MethodsTen matched human lower extremity pairs were randomly assigned to first TMTJ arthrodesis using either 2 crossed headed 4.0-mm cannulated compression screws (HS) or two 4.0-mm cannulated headless compression screws (HLS). After bone mineral density (BMD) assessment, specimens were cyclically loaded from 0 to 31 N for 1000 cycles. Dorsal angulation and construct stiffness were measured during cyclic loading and subsequent loading to failure.ResultsMean stiffness during ultimate load testing was 58.91 ± 31.33 N/mm for headed screws and 68.36 ± 84.29 N/mm for headless screws (P = .842). Mean yield load was 115.80 ± 61.94 and 67.79 ± 35.90 N (P = .101), and mean ultimate load was 142.10 ± 65.24 and 83.02 ± 60.77 N (P = 0.064), respectively. No significant difference in dorsal angulation was observed. Mean BMD was 0.547 ± 0.222 g/cm² for headed screws and 0.533 ± 0.204 g/cm² for headless screws (P = 0.897). Bone mineral density positively correlated with construct stiffness in the headless screw group during several loading cycles, but not in the headed screw group. No significant correlations were found between BMD and yield or ultimate load.ConclusionHeaded and headless crossed screw constructs showed no statistically significant differences in stiffness, yield load, ultimate load, or dorsal angulation. However, the numerical difference in ultimate load favored headed screws. Headless compression screws may offer clinical advantages through their low-profile design, but further biomechanical and clinical studies are warranted.Clinical Relevance:Headless and headed screws showed no statistically significant differences in this cadaveric first tarsometatarsal joint model, although headed screws achieved higher mean failure loads. Their low-profile design may reduce hardware prominence and soft tissue irritation while maintaining adequate primary fixation stability.

Foot & Ankle Specialist
University of British Columbia (CA), Hanusch Hospital (AT), Medical University of Vienna (AT)
Good health and well-being
Foot and Ankle Surgery
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon