Effects of PCD Tool Geometry on Turning GFRP Thin-Walled Tubes for Lightning Isolators

Thin-walled glass-fiber/epoxy tubes containing conductive carbon black are used in lightning isolators for aircraft fuel tanks. Although tool geometry has been studied in the cutting of glass-fiber-reinforced polymers (GFRPs), much of the existing work relies on two-dimensional orthogonal cutting. Its effects during the external turning of conductive GFRP thin-walled tubes remain insufficiently understood. This study therefore used polycrystalline diamond (PCD) tools in single-factor turning experiments to investigate the effects of rake angle, clearance angle, inclination angle, and nose radius on cutting forces, temperature, and surface roughness (Ra and Rt). The cutting speed, feed, and depth of cut were fixed at 300 m/min, 0.1 mm/rev, and 0.3 mm, respectively. Each experimental condition was repeated independently three times, and the results were evaluated using Welch ANOVA with Holm correction and Games–Howell post hoc comparisons. Increasing the rake angle from 0° to 20° reduced the resultant cutting force and surface roughness overall. The observed cutting-zone temperature increased, whereas the workpiece surface temperature decreased. As the clearance angle increased, the feed force, main cutting force, and measured temperatures initially increased and then decreased, while radial force and surface roughness changed relatively little. Increasing the inclination angle from 0° to 12° produced a similar nonmonotonic response in cutting forces and temperatures, with limited effects on roughness. Changes in nose radius altered the distribution of cutting-force components: the observed cutting-zone temperature decreased as the radius increased from 0.2 to 0.8 mm, then rose at 1.0 mm, while surface roughness increased slightly overall. Statistical analysis indicated significant overall effects of tool geometry on cutting forces, whereas the effects on Ra and Rt were not statistically significant after Holm correction. These findings characterize the distinct effects of PCD tool geometry on the mechanical, thermal, and surface-quality responses of conductive GFRP thin-walled tubes, providing an experimental basis for tool-geometry selection in external turning.

Authors

Institutions

Publication Details

Journal
Materials
Published
2026-11-18
DOI
https://doi.org/10.3390/ma19224874
Primary Topic
Advanced machining processes and optimization
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Effects of PCD Tool Geometry on Turning GFRP Thin-Walled Tubes for Lightning Isolators

Shi Hua, Yupu Zhang, Liang Ge, Zhonghan Cui et al.
Materials
Advanced machining processes and optimization
article

Effects of PCD Tool Geometry on Turning GFRP Thin-Walled Tubes for Lightning Isolators

Shi Hua, Yupu Zhang, Liang Ge, Zhonghan Cui, Chengwei Liu, Yihan Liu, Shutao Huang
article en

Abstract

Thin-walled glass-fiber/epoxy tubes containing conductive carbon black are used in lightning isolators for aircraft fuel tanks. Although tool geometry has been studied in the cutting of glass-fiber-reinforced polymers (GFRPs), much of the existing work relies on two-dimensional orthogonal cutting. Its effects during the external turning of conductive GFRP thin-walled tubes remain insufficiently understood. This study therefore used polycrystalline diamond (PCD) tools in single-factor turning experiments to investigate the effects of rake angle, clearance angle, inclination angle, and nose radius on cutting forces, temperature, and surface roughness (Ra and Rt). The cutting speed, feed, and depth of cut were fixed at 300 m/min, 0.1 mm/rev, and 0.3 mm, respectively. Each experimental condition was repeated independently three times, and the results were evaluated using Welch ANOVA with Holm correction and Games–Howell post hoc comparisons. Increasing the rake angle from 0° to 20° reduced the resultant cutting force and surface roughness overall. The observed cutting-zone temperature increased, whereas the workpiece surface temperature decreased. As the clearance angle increased, the feed force, main cutting force, and measured temperatures initially increased and then decreased, while radial force and surface roughness changed relatively little. Increasing the inclination angle from 0° to 12° produced a similar nonmonotonic response in cutting forces and temperatures, with limited effects on roughness. Changes in nose radius altered the distribution of cutting-force components: the observed cutting-zone temperature decreased as the radius increased from 0.2 to 0.8 mm, then rose at 1.0 mm, while surface roughness increased slightly overall. Statistical analysis indicated significant overall effects of tool geometry on cutting forces, whereas the effects on Ra and Rt were not statistically significant after Holm correction. These findings characterize the distinct effects of PCD tool geometry on the mechanical, thermal, and surface-quality responses of conductive GFRP thin-walled tubes, providing an experimental basis for tool-geometry selection in external turning.

MaterialsVol. 19(22)
Shenyang Ligong University (CN)
Advanced machining processes and optimization
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon