Ultrastretchable Liquid-Metal Reinforced Polyelectrolyte Hydrogel Sensors for Multichannel Gesture Recognition and Robotic-Hand Control

With the development of wearable devices, human-motion monitoring, and human-machine interaction technologies, flexible sensing materials with high stretchability, rapid response, high sensitivity, and cyclic stability are increasingly required. To address conductive-pathway instability under large and repeated deformation, interfacial failure associated with layered liquid-metal/hydrogel architectures, and the difficulty in balancing mechanical deformability with sensing performance, this work reports a liquid-metal-reinforced polyelectrolyte hydrogel based on (2-(acryloyloxy)ethyl)trimethylammonium chloride (AETC) and eutectic gallium-indium (EGaIn) microdroplets. EGaIn was ultrasonically dispersed in water, introduced into an aqueous AETC precursor, and immobilized within the poly(AETC) network through UV-induced radical polymerization, yielding a bulk-dispersed AETC@LM hydrogel, where AETC@LM denotes an AETC-derived polyelectrolyte hydrogel containing dispersed EGaIn microdroplets. The effects of liquid-metal content on the morphology, chemical structure, mechanical properties, water retention, adhesion, and electromechanical sensing performance of the hydrogels were systematically investigated. Among the investigated formulations, LM200, prepared with 200 μL of the liquid-metal dispersion, exhibited the most favorable overall performance. It sustained a maximum tensile strain of approximately 3000% and provided strain sensing over 0-900%. Piecewise least-squares linear fitting of the strain response yielded gauge factors of 1.4 and 11.3 in the low- and high-strain regions, respectively. Similarly, piecewise least-squares linear fitting of the pressure response yielded sensitivities of 8.07 kPa-1 over approximately 0-7 kPa and 0.68 kPa-1 over approximately 8-25 kPa. LM200 retained approximately 95% of its initial mass after four weeks of ambient storage and exhibited adhesion to different substrates, with the highest adhesion strength observed on wood. The sensor showed response and recovery times of 0.24 and 0.18 s, respectively, and maintained repeatable resistance responses over 600 tensile cycles at 50% strain. Furthermore, five LM200 sensors were integrated into a five-channel smart glove. A ResNet50-based residual-learning model classified ten representative gestures from the acquired multichannel signals, which were also mapped to corresponding robotic-hand postures. The principal innovation of this work is the material-to-system integration of a bulk-dispersed liquid-metal/AETC polyelectrolyte architecture with strain-pressure dual-mode sensing and machine-learning-assisted multichannel gesture recognition. This integrated strategy establishes a structure-property-application relationship for liquid-metal-reinforced polyelectrolyte hydrogels and provides an experimental basis for large-deformation wearable sensing and intelligent human-machine interaction.

Authors

Institutions

Publication Details

Journal
ACS Applied Materials & Interfaces
Published
2026-11-18
DOI
https://doi.org/10.1021/acsami.6c19768
Primary Topic
Advanced Sensor and Energy Harvesting Materials
Type
article
Field-Weighted Citation Impact
0.00

Funders

Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Ultrastretchable Liquid-Metal Reinforced Polyelectrolyte Hydrogel Sensors for Multichannel Gesture Recognition and Robotic-Hand Control

Tianchi Chen, Hui Chen, Xiangning Lu, Yaming Hu et al.
3 links
ACS Applied Materials & Interfaces
Advanced Sensor and Energy Harvesting Materials
article

Ultrastretchable Liquid-Metal Reinforced Polyelectrolyte Hydrogel Sensors for Multichannel Gesture Recognition and Robotic-Hand Control

Tianchi Chen, Hui Chen, Xiangning Lu, Yaming Hu, Xuqing Song
article en

Abstract

With the development of wearable devices, human-motion monitoring, and human-machine interaction technologies, flexible sensing materials with high stretchability, rapid response, high sensitivity, and cyclic stability are increasingly required. To address conductive-pathway instability under large and repeated deformation, interfacial failure associated with layered liquid-metal/hydrogel architectures, and the difficulty in balancing mechanical deformability with sensing performance, this work reports a liquid-metal-reinforced polyelectrolyte hydrogel based on (2-(acryloyloxy)ethyl)trimethylammonium chloride (AETC) and eutectic gallium-indium (EGaIn) microdroplets. EGaIn was ultrasonically dispersed in water, introduced into an aqueous AETC precursor, and immobilized within the poly(AETC) network through UV-induced radical polymerization, yielding a bulk-dispersed AETC@LM hydrogel, where AETC@LM denotes an AETC-derived polyelectrolyte hydrogel containing dispersed EGaIn microdroplets. The effects of liquid-metal content on the morphology, chemical structure, mechanical properties, water retention, adhesion, and electromechanical sensing performance of the hydrogels were systematically investigated. Among the investigated formulations, LM200, prepared with 200 μL of the liquid-metal dispersion, exhibited the most favorable overall performance. It sustained a maximum tensile strain of approximately 3000% and provided strain sensing over 0-900%. Piecewise least-squares linear fitting of the strain response yielded gauge factors of 1.4 and 11.3 in the low- and high-strain regions, respectively. Similarly, piecewise least-squares linear fitting of the pressure response yielded sensitivities of 8.07 kPa-1 over approximately 0-7 kPa and 0.68 kPa-1 over approximately 8-25 kPa. LM200 retained approximately 95% of its initial mass after four weeks of ambient storage and exhibited adhesion to different substrates, with the highest adhesion strength observed on wood. The sensor showed response and recovery times of 0.24 and 0.18 s, respectively, and maintained repeatable resistance responses over 600 tensile cycles at 50% strain. Furthermore, five LM200 sensors were integrated into a five-channel smart glove. A ResNet50-based residual-learning model classified ten representative gestures from the acquired multichannel signals, which were also mapped to corresponding robotic-hand postures. The principal innovation of this work is the material-to-system integration of a bulk-dispersed liquid-metal/AETC polyelectrolyte architecture with strain-pressure dual-mode sensing and machine-learning-assisted multichannel gesture recognition. This integrated strategy establishes a structure-property-application relationship for liquid-metal-reinforced polyelectrolyte hydrogels and provides an experimental basis for large-deformation wearable sensing and intelligent human-machine interaction.

ACS Applied Materials & Interfaces
Jiangsu Normal University (CN)
National Natural Science Foundation of China, Natural Science Foundation of Jiangsu Province, Natural Science Research of Jiangsu Higher Education Institutions of China
Advanced Sensor and Energy Harvesting Materials
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon