LIGHT AIRCRAFT PROPELLER

This work presents the design and computer-aided analysis of a two-blade, fixed-pitch propeller for a light aircraft powered by a four-cylinder engine of about 75 kW that turns the propeller directly at 2500 rpm. The propeller has a diameter of 1.75 m and a geometric pitch of 1.40 m at three-quarter radius, and it is intended for a two-seat training aircraft that cruises at about 180 km/h. The aim of the study is to arrive at a blade shape and a blade material that give good cruise efficiency, adequate static thrust for take-off, and a safe structural margin under the loads that act on a rotating blade. The blade geometry was obtained with blade-element momentum theory. The blade was divided into twenty radial stations, and at each station the chord and twist angle were chosen so that the Clark-Y section works close to its best lift-to-drag ratio at the cruise advance ratio of 0.686. The resulting blade has a maximum chord of 135 mm at 35 percent radius, a tip chord of 70 mm, and a twist that falls from 42 degrees near the root to 15.5 degrees at the tip. The geometry was modelled in SolidWorks as a lofted solid through the twenty sections and exported to the analysis tools. Aerodynamic performance was predicted in ANSYS Fluent using a rotating reference frame on a 180 degree periodic sector with about 4.2 million polyhedral cells and the k-omega SST turbulence model. At the design point of 50 m/s and 2500 rpm the computed thrust is 968 N, the shaft torque is 229 N m, and the propulsive efficiency is 0.807. The peak efficiency of 0.83 occurs at an advance ratio of 0.75, and the static thrust at zero forward speed is 1980 N. The blade-element estimate of cruise thrust was 1012 N, which lies within 4.5 percent of the CFD result. The pressure field from the CFD solution was mapped onto the blade surface in ANSYS Mechanical and combined with the centrifugal load at 261.8 rad/s for static structural and pre-stressed modal analysis. Three blade materials were compared: a birch wood laminate, aluminium alloy 2024-T3, and a carbon/epoxy composite. The composite blade has the lowest propeller mass of 4.1 kg, a peak von Mises stress of 61.5 MPa, a tip deflection of 2.7 mm, and a first flapwise frequency of 148 Hz. The aluminium blade weighs 10.9 kg for the propeller, and the wood blade has a first mode only 15 percent above the 2P excitation.

Authors

Publication Details

Journal
International Journal of AI Electrical Civil and Mechanical engineering
Published
2026-11-17
DOI
https://doi.org/10.64751/w8f8s049
Primary Topic
Advanced Aircraft Design and Technologies
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

LIGHT AIRCRAFT PROPELLER

S. Sai Ram Reddy, A.Mallikarjun, S.Joshua, MD. Subahan, G.Navadeep
International Journal of AI Electrical Civil and Mechanical engineering
Advanced Aircraft Design and Technologies
article

LIGHT AIRCRAFT PROPELLER

S. Sai Ram Reddy, A.Mallikarjun, S.Joshua, MD. Subahan, G.Navadeep
article en

Abstract

This work presents the design and computer-aided analysis of a two-blade, fixed-pitch propeller for a light aircraft powered by a four-cylinder engine of about 75 kW that turns the propeller directly at 2500 rpm. The propeller has a diameter of 1.75 m and a geometric pitch of 1.40 m at three-quarter radius, and it is intended for a two-seat training aircraft that cruises at about 180 km/h. The aim of the study is to arrive at a blade shape and a blade material that give good cruise efficiency, adequate static thrust for take-off, and a safe structural margin under the loads that act on a rotating blade. The blade geometry was obtained with blade-element momentum theory. The blade was divided into twenty radial stations, and at each station the chord and twist angle were chosen so that the Clark-Y section works close to its best lift-to-drag ratio at the cruise advance ratio of 0.686. The resulting blade has a maximum chord of 135 mm at 35 percent radius, a tip chord of 70 mm, and a twist that falls from 42 degrees near the root to 15.5 degrees at the tip. The geometry was modelled in SolidWorks as a lofted solid through the twenty sections and exported to the analysis tools. Aerodynamic performance was predicted in ANSYS Fluent using a rotating reference frame on a 180 degree periodic sector with about 4.2 million polyhedral cells and the k-omega SST turbulence model. At the design point of 50 m/s and 2500 rpm the computed thrust is 968 N, the shaft torque is 229 N m, and the propulsive efficiency is 0.807. The peak efficiency of 0.83 occurs at an advance ratio of 0.75, and the static thrust at zero forward speed is 1980 N. The blade-element estimate of cruise thrust was 1012 N, which lies within 4.5 percent of the CFD result. The pressure field from the CFD solution was mapped onto the blade surface in ANSYS Mechanical and combined with the centrifugal load at 261.8 rad/s for static structural and pre-stressed modal analysis. Three blade materials were compared: a birch wood laminate, aluminium alloy 2024-T3, and a carbon/epoxy composite. The composite blade has the lowest propeller mass of 4.1 kg, a peak von Mises stress of 61.5 MPa, a tip deflection of 2.7 mm, and a first flapwise frequency of 148 Hz. The aluminium blade weighs 10.9 kg for the propeller, and the wood blade has a first mode only 15 percent above the 2P excitation.

International Journal of AI Electrical Civil and Mechanical engineering
Advanced Aircraft Design and Technologies
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon