Enhanced Congo Red adsorption by chitosan graft polyacrylamide hydrogel incorporating diatomite supported Fe–Ni layered double hydroxide

This research aimed to enhance the adsorptive properties of chitosan-grafted-polyacrylamide Poly(AAM) copolymeric hydrogels through the incorporation of Fe–Ni layered double hydroxide (LDH)-loaded diatomite. The synthesized adsorbents were characterized using various analytical techniques, including BET, FTIR, XRD, SEM–EDS, and elemental mapping. The results confirmed the successful immobilization of diatomite–LDH within the hydrogel network. Furthermore, BET analysis revealed enhanced porosity of the composites after modification. The adsorption performance of the prepared adsorbents was assessed for the removal of Congo Red (CR), an anionic dye, using batch adsorption experiments. The effects of key parameters—namely temperature, contact time, adsorbent dosage, initial dye concentration, and pH—on the adsorption efficiency were systematically evaluated. The maximum experimental adsorption capacity for CR removal was found to be 9.702 mg·g⁻¹ under the following conditions: 25 °C, pH = 5, initial dye concentration of 10 mg.L⁻¹, contact time of 150 min, and adsorbent dosage of 1 g.L⁻¹. Kinetic studies indicated that the adsorption process followed the pseudo-first-order kinetic model. Isotherm analysis showed that the Langmuir model provided the best fit for CS-g-Poly(AAM) and CS-g-Poly(AAM)/Diatomite, consistent with monolayer adsorption, whereas the Freundlich model gave a slightly higher R² value (0.982) than the Langmuir model (0.971) for CS-g-Poly(AAM)/Diatomite/Ni–Fe LDH, suggesting that adsorption onto this composite may be governed by multilayer adsorption on heterogeneous surfaces. The favorable nature of CR adsorption onto all adsorbents was supported by the dimensionless separation factor (R L ) and the Freundlich n values. The mean adsorption energies obtained from the Dubinin–Radushkevich isotherm (0.418, 0.249, and 0.365 kJ.mol⁻¹) indicated that physical adsorption interactions contributed substantially to CR uptake. Thermodynamic investigations demonstrated that the adsorption process was spontaneous and exothermic in nature. The influence of interfering ions revealed that the presence of Na⁺ and Ca²⁺ cations in the solution decreased the adsorption efficiency. Moreover, the synthesized adsorbents exhibited excellent reusability, maintaining their adsorption performance over six consecutive adsorption–desorption cycles.

Authors

Institutions

Publication Details

Journal
Scientific Reports
Published
2026-11-18
DOI
https://doi.org/10.1038/s41598-026-80923-1
Primary Topic
Adsorption and biosorption for pollutant removal
Type
article
Field-Weighted Citation Impact
0.00

Funders

Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Enhanced Congo Red adsorption by chitosan graft polyacrylamide hydrogel incorporating diatomite supported Fe–Ni layered double hydroxide

Mohaddeseh Mardani, Ali Akbari, Naeimeh Sadat Peighambardoust, Seyed Jamaleddin Peighambardoust
Scientific Reports
Adsorption and biosorption for pollutant removal
article

Enhanced Congo Red adsorption by chitosan graft polyacrylamide hydrogel incorporating diatomite supported Fe–Ni layered double hydroxide

Mohaddeseh Mardani, Ali Akbari, Naeimeh Sadat Peighambardoust, Seyed Jamaleddin Peighambardoust
article en

Abstract

This research aimed to enhance the adsorptive properties of chitosan-grafted-polyacrylamide Poly(AAM) copolymeric hydrogels through the incorporation of Fe–Ni layered double hydroxide (LDH)-loaded diatomite. The synthesized adsorbents were characterized using various analytical techniques, including BET, FTIR, XRD, SEM–EDS, and elemental mapping. The results confirmed the successful immobilization of diatomite–LDH within the hydrogel network. Furthermore, BET analysis revealed enhanced porosity of the composites after modification. The adsorption performance of the prepared adsorbents was assessed for the removal of Congo Red (CR), an anionic dye, using batch adsorption experiments. The effects of key parameters—namely temperature, contact time, adsorbent dosage, initial dye concentration, and pH—on the adsorption efficiency were systematically evaluated. The maximum experimental adsorption capacity for CR removal was found to be 9.702 mg·g⁻¹ under the following conditions: 25 °C, pH = 5, initial dye concentration of 10 mg.L⁻¹, contact time of 150 min, and adsorbent dosage of 1 g.L⁻¹. Kinetic studies indicated that the adsorption process followed the pseudo-first-order kinetic model. Isotherm analysis showed that the Langmuir model provided the best fit for CS-g-Poly(AAM) and CS-g-Poly(AAM)/Diatomite, consistent with monolayer adsorption, whereas the Freundlich model gave a slightly higher R² value (0.982) than the Langmuir model (0.971) for CS-g-Poly(AAM)/Diatomite/Ni–Fe LDH, suggesting that adsorption onto this composite may be governed by multilayer adsorption on heterogeneous surfaces. The favorable nature of CR adsorption onto all adsorbents was supported by the dimensionless separation factor (R L ) and the Freundlich n values. The mean adsorption energies obtained from the Dubinin–Radushkevich isotherm (0.418, 0.249, and 0.365 kJ.mol⁻¹) indicated that physical adsorption interactions contributed substantially to CR uptake. Thermodynamic investigations demonstrated that the adsorption process was spontaneous and exothermic in nature. The influence of interfering ions revealed that the presence of Na⁺ and Ca²⁺ cations in the solution decreased the adsorption efficiency. Moreover, the synthesized adsorbents exhibited excellent reusability, maintaining their adsorption performance over six consecutive adsorption–desorption cycles.

Scientific Reports
University of Tabriz (IR), Istinye University (TR)
University of Tabriz
Adsorption and biosorption for pollutant removal
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon