Mechanical Properties and Impact-Sliding Wear of AISI 1020 Steel after Electrochemical Boriding and Subsequent Heat Treatment

AISI 1020 steel is widely used in engineering applications owing to its low cost and good formability; however, its relatively low surface hardness limits its wear resistance under severe contact conditions. This study investigated the mechanical and tribological response of AISI 1020 steel subjected to a hybrid treatment combining electrochemical boriding with subsequent thermal treatment and water quenching. Electrochemical boriding was performed at 950 °C under a current density of 200 mA cm-2 for 15 min. After the electrical current was interrupted, the specimens were cooled in the molten electrolyte to a furnace-indicated temperature of 725 °C, held for 30 min, and quenched in water. Cross-sectional microscopy revealed a predominantly light-contrast boride layer approximately 50 μm thick. X-ray diffraction identified Fe2B reflections without distinct detectable FeB reflections, supporting the formation of an Fe2B-dominant layer. The treated surface exhibited a hardness of 1744 ± 100 HV0.05. Ultimate tensile strength increased from 738 to 832 MPa, whereas total elongation decreased from 22.8% to 10.8%. Under the investigated impact-sliding conditions, wear volume per cycle decreased by approximately 11% in the impact-dominated region and 16% in the sliding-dominated region relative to untreated steel. Localized cracking was nevertheless observed in the treated surface after impact loading. These findings demonstrate that the combined treatment reduced wear under the tested conditions while introducing a trade-off between increased ultimate tensile strength and reduced tensile ductility.

Authors

Institutions

Publication Details

Journal
GAZI UNIVERSITY JOURNAL OF SCIENCE
Published
2026-11-18
DOI
https://doi.org/10.35378/gujs.1917714
Primary Topic
Surface Treatment and Coatings
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Mechanical Properties and Impact-Sliding Wear of AISI 1020 Steel after Electrochemical Boriding and Subsequent Heat Treatment

Harun Mindivan, Eda Tuzcu Şahin
2 links
GAZI UNIVERSITY JOURNAL OF SCIENCE
Surface Treatment and Coatings
article

Mechanical Properties and Impact-Sliding Wear of AISI 1020 Steel after Electrochemical Boriding and Subsequent Heat Treatment

Harun Mindivan, Eda Tuzcu Şahin
article en

Abstract

AISI 1020 steel is widely used in engineering applications owing to its low cost and good formability; however, its relatively low surface hardness limits its wear resistance under severe contact conditions. This study investigated the mechanical and tribological response of AISI 1020 steel subjected to a hybrid treatment combining electrochemical boriding with subsequent thermal treatment and water quenching. Electrochemical boriding was performed at 950 °C under a current density of 200 mA cm-2 for 15 min. After the electrical current was interrupted, the specimens were cooled in the molten electrolyte to a furnace-indicated temperature of 725 °C, held for 30 min, and quenched in water. Cross-sectional microscopy revealed a predominantly light-contrast boride layer approximately 50 μm thick. X-ray diffraction identified Fe2B reflections without distinct detectable FeB reflections, supporting the formation of an Fe2B-dominant layer. The treated surface exhibited a hardness of 1744 ± 100 HV0.05. Ultimate tensile strength increased from 738 to 832 MPa, whereas total elongation decreased from 22.8% to 10.8%. Under the investigated impact-sliding conditions, wear volume per cycle decreased by approximately 11% in the impact-dominated region and 16% in the sliding-dominated region relative to untreated steel. Localized cracking was nevertheless observed in the treated surface after impact loading. These findings demonstrate that the combined treatment reduced wear under the tested conditions while introducing a trade-off between increased ultimate tensile strength and reduced tensile ductility.

GAZI UNIVERSITY JOURNAL OF SCIENCE(Advanced Online Publication)
Bilecik Şeyh Edebali Üniversitesi (TR)
Surface Treatment and Coatings
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon