Two‐Dimensional Plate Model Perturbation for Calculation of Stiffness and Damping Coefficients of Foil Bearings

Foil bearings are widely adopted in high‐speed turbomachinery as oil‐free support systems, but the accurate prediction of rotordynamic coefficients remains a critical challenge. Conventional first‐order perturbation models commonly use inertia‐less spring‐dampers assigned to every nodal point of the zeroth‐order pressure grid. This study develops a new perturbation model by directly perturbing the two‐dimensional (2D) top‐foil plate equation with physical bump locations, spanwise bending of the top foil, and foil inertia. The influence of foil inertia is first examined by comparing the 2D plate perturbation model with and without foil mass. For the present bearing configuration and investigated speed and excitation‐frequency ranges, foil inertia produces only small changes in the calculated stiffness and damping coefficients. The massless 2D plate perturbation model is then compared with the conventional perturbation method using the same zeroth‐order solution. Both models predict comparable trends with rotor speed and excitation‐frequency ratio but different coefficient magnitudes. At 70,000 rpm under synchronous excitation, the 2D plate perturbation model predicts the direct stiffness and damping coefficients approximately 2.6%–14.4% lower than those obtained using the virtual independent elastic‐foundation (VIEF) model. This difference is attributed to the first‐order foil‐deformation model because the 2D plate formulation retains continuous top‐foil bending while applying stiffness and damping only at physical bump locations. The proposed method therefore provides a more physically representative first‐order perturbation formulation that captures the structurally coupled foil response.

Authors

Institutions

Publication Details

Journal
Journal of Tribology
Published
2026-11-18
DOI
https://doi.org/10.1002/jtrb.70016
Primary Topic
Tribology and Lubrication Engineering
Type
article
Field-Weighted Citation Impact
0.00

Funders

Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Two‐Dimensional Plate Model Perturbation for Calculation of Stiffness and Damping Coefficients of Foil Bearings

김대종, Rafid Imam
Journal of Tribology
Tribology and Lubrication Engineering
article

Two‐Dimensional Plate Model Perturbation for Calculation of Stiffness and Damping Coefficients of Foil Bearings

김대종, Rafid Imam
article en

Abstract

Foil bearings are widely adopted in high‐speed turbomachinery as oil‐free support systems, but the accurate prediction of rotordynamic coefficients remains a critical challenge. Conventional first‐order perturbation models commonly use inertia‐less spring‐dampers assigned to every nodal point of the zeroth‐order pressure grid. This study develops a new perturbation model by directly perturbing the two‐dimensional (2D) top‐foil plate equation with physical bump locations, spanwise bending of the top foil, and foil inertia. The influence of foil inertia is first examined by comparing the 2D plate perturbation model with and without foil mass. For the present bearing configuration and investigated speed and excitation‐frequency ranges, foil inertia produces only small changes in the calculated stiffness and damping coefficients. The massless 2D plate perturbation model is then compared with the conventional perturbation method using the same zeroth‐order solution. Both models predict comparable trends with rotor speed and excitation‐frequency ratio but different coefficient magnitudes. At 70,000 rpm under synchronous excitation, the 2D plate perturbation model predicts the direct stiffness and damping coefficients approximately 2.6%–14.4% lower than those obtained using the virtual independent elastic‐foundation (VIEF) model. This difference is attributed to the first‐order foil‐deformation model because the 2D plate formulation retains continuous top‐foil bending while applying stiffness and damping only at physical bump locations. The proposed method therefore provides a more physically representative first‐order perturbation formulation that captures the structurally coupled foil response.

Journal of Tribology
The University of Texas at Arlington (US)
U.S. Navy, Office of Naval Research
Tribology and Lubrication Engineering
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon