Orientation of flat fibers in injection molding: a two-tensor Folgar–Tucker model, fitted closures, and properties for warpage simulation

Flat (ribbon-like) glass fibers, such as 28 × 7 µm E-glass, are used in injection-molded thermoplastics to raise transverse stiffness and lower warpage, but orientation models and the micromechanics in molding simulation assume axisymmetric fibers. We generalize the Folgar–Tucker model to triaxial particles. Single fibers are described by unit quaternions obeying the triaxial Jeffery equation. Because the orientation space is S³/Q₈, the quaternion second moment carries no information, and the macroscopic state consists of two second-order tensors: A for the length axis and C for the normal of the flat face. The moment equations are exact in the rotary-diffusion term, also for anisotropic diffusion in the particle frame, and need a closure only for three mixed fourth-order moments. A frame-indifferent closure with 57 basis tensors, whose coefficients depend on the invariants and on two shape parameters, is fitted to 2,156 quaternion Monte Carlo runs and covers rods, ribbons and disks with 2–4% flow-term error. At weak rotary diffusion a blend with a decoupled closure gives the most accurate trajectories. Mori–Tanaka homogenization with the triaxial Eshelby tensor, together with an orientation average that is exact in the same moments, predicts 9–16% higher cross-flow stiffness and a 19% smaller in-plane thermal-expansion anisotropy than round fibers of equal cross-section. To use the model in a commercial code that accepts only one orientation tensor, we identify that code's property model from published descriptions and its outputs to within 1.1%, and pass a fitted effective tensor A_eff. This reproduces the flat-fiber warpage driver (median error −0.5 µm/m/K instead of +7.7 µm/m/K) and predicts about 30% lower shrinkage anisotropy for a center-gated disk and 5% lower warpage for a tray in a linear analysis; past buckling, a large-deflection analysis amplifies this to 17%. Main contributions Two-tensor (A, C) orientation model for flat fibers, derived from quaternion kinematics on SO(3). Closure fitted to Monte Carlo data across a family of shapes, valid for rods, ribbons and disks. Thermoelastic properties of flat-fiber composites from Mori–Tanaka homogenization with the triaxial Eshelby tensor. Coupling to a commercial 3D molding solver through a solver plugin and a fitted effective orientation tensor. About this preprint. 37 pages, 7 figures, 11 tables. Conference abstracts based on this work were submitted on 28 October 2026 to NUMIFORM 2027 (Kyoto, submission No. 052) and PPS-42 (Chengdu, reference 26). The code, fitted closures and calibration data are available from the author on reasonable request. Autodesk and Moldflow are registered trademarks or trademarks of Autodesk, Inc. This work is not affiliated with or endorsed by Autodesk, Inc.

Authors

Publication Details

Journal
Zenodo (CERN European Organization for Nuclear Research)
Published
2026-11-17
DOI
https://doi.org/10.5281/zenodo.24307739
Primary Topic
Injection Molding Process and Properties
Type
preprint
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
preprint

Orientation of flat fibers in injection molding: a two-tensor Folgar–Tucker model, fitted closures, and properties for warpage simulation

Alexander Bakharev
Zenodo (CERN European Organization for Nuclear Research)
Injection Molding Process and Properties
preprint

Orientation of flat fibers in injection molding: a two-tensor Folgar–Tucker model, fitted closures, and properties for warpage simulation

Alexander Bakharev
preprint en

Abstract

Flat (ribbon-like) glass fibers, such as 28 × 7 µm E-glass, are used in injection-molded thermoplastics to raise transverse stiffness and lower warpage, but orientation models and the micromechanics in molding simulation assume axisymmetric fibers. We generalize the Folgar–Tucker model to triaxial particles. Single fibers are described by unit quaternions obeying the triaxial Jeffery equation. Because the orientation space is S³/Q₈, the quaternion second moment carries no information, and the macroscopic state consists of two second-order tensors: A for the length axis and C for the normal of the flat face. The moment equations are exact in the rotary-diffusion term, also for anisotropic diffusion in the particle frame, and need a closure only for three mixed fourth-order moments. A frame-indifferent closure with 57 basis tensors, whose coefficients depend on the invariants and on two shape parameters, is fitted to 2,156 quaternion Monte Carlo runs and covers rods, ribbons and disks with 2–4% flow-term error. At weak rotary diffusion a blend with a decoupled closure gives the most accurate trajectories. Mori–Tanaka homogenization with the triaxial Eshelby tensor, together with an orientation average that is exact in the same moments, predicts 9–16% higher cross-flow stiffness and a 19% smaller in-plane thermal-expansion anisotropy than round fibers of equal cross-section. To use the model in a commercial code that accepts only one orientation tensor, we identify that code's property model from published descriptions and its outputs to within 1.1%, and pass a fitted effective tensor A_eff. This reproduces the flat-fiber warpage driver (median error −0.5 µm/m/K instead of +7.7 µm/m/K) and predicts about 30% lower shrinkage anisotropy for a center-gated disk and 5% lower warpage for a tray in a linear analysis; past buckling, a large-deflection analysis amplifies this to 17%. Main contributions Two-tensor (A, C) orientation model for flat fibers, derived from quaternion kinematics on SO(3). Closure fitted to Monte Carlo data across a family of shapes, valid for rods, ribbons and disks. Thermoelastic properties of flat-fiber composites from Mori–Tanaka homogenization with the triaxial Eshelby tensor. Coupling to a commercial 3D molding solver through a solver plugin and a fitted effective orientation tensor. About this preprint. 37 pages, 7 figures, 11 tables. Conference abstracts based on this work were submitted on 28 October 2026 to NUMIFORM 2027 (Kyoto, submission No. 052) and PPS-42 (Chengdu, reference 26). The code, fitted closures and calibration data are available from the author on reasonable request. Autodesk and Moldflow are registered trademarks or trademarks of Autodesk, Inc. This work is not affiliated with or endorsed by Autodesk, Inc.

Zenodo (CERN European Organization for Nuclear Research)
Injection Molding Process and Properties
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon