Surrogate-Assisted Tolerance and Identifiability Analysis of Manufacturing Deviations in a 28-GHz mmWave Antenna from S11 Measurements

This paper presents a surrogate-assisted study of the tolerance and of the identifiability of manufacturing deviations of a 28 GHz inset-fed microstrip patch antenna for 5G millimeter-wave applications. A Multilayer Perceptron (MLP) surrogate was trained on 500,625 (geometry, frequency) samples (625 full-wave HFSS geometries × 801 frequency points) and reaches R2 = 0.996 on unseen geometries. The geometry selected from the simulations achieves a simulated matching of −43 dB at 28 GHz, a 2.75 GHz bandwidth and a simulated gain of 4.4 dBi; the contribution of this work is not the antenna itself, which is a conventional benchmark. The fabricated prototype resonates at 28.07 GHz against 28.02 GHz in simulation, i.e., within 50 MHz (0.18%). The same full-factorial database (±100 µm around the fabricated design) shows that S11 at 28 GHz remains below −26 dB for every combination of deviations and that y1 is the geometrical parameter that most affects the resonance frequency, followed by x1, y2 and x2. A Bayesian inverse analysis based on the MLP shows, on a blind simulated test and on the measured curve, that S11 alone only partially identifies the individual deviations (only y1 is recovered, and the 90% intervals contain the true value in 50–67% of the cases). Moreover, additional ANSYS HFSS (version .13, Ansys Inc., Canonsburg, PA, USA) simulations show that a change of only −0.3% of the FR4 permittivity or −13 µm of its thickness reproduces the measured 50 MHz shift, whereas ±100 µm of any geometrical parameter shifts the resonance by at most ±40 MHz. The substrate therefore dominates over the geometrical deviations, and when a substrate nuisance parameter is included in the inverse analysis (approximate model), none of the four geometrical deviations is identified from S11. These results delimit what can and cannot be diagnosed from a single S11 measurement, and provide guidelines for the validation of fabricated mmWave antennas (direct dimensional measurements and substrate characterization).

Authors

Institutions

Publication Details

Journal
Electronics
Published
2026-11-17
DOI
https://doi.org/10.3390/electronics15225360
Primary Topic
Antenna Design and Analysis
Type
article
Field-Weighted Citation Impact
0.00

Funders

Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Surrogate-Assisted Tolerance and Identifiability Analysis of Manufacturing Deviations in a 28-GHz mmWave Antenna from S11 Measurements

Linda Chouikhi, Mongi Ben Moussa, Hédi Sakli, Chaker Essid et al.
1 links
Electronics
Antenna Design and Analysis
article

Surrogate-Assisted Tolerance and Identifiability Analysis of Manufacturing Deviations in a 28-GHz mmWave Antenna from S11 Measurements

Linda Chouikhi, Mongi Ben Moussa, Hédi Sakli, Chaker Essid, Abdelilah Mansour
article en

Abstract

This paper presents a surrogate-assisted study of the tolerance and of the identifiability of manufacturing deviations of a 28 GHz inset-fed microstrip patch antenna for 5G millimeter-wave applications. A Multilayer Perceptron (MLP) surrogate was trained on 500,625 (geometry, frequency) samples (625 full-wave HFSS geometries × 801 frequency points) and reaches R2 = 0.996 on unseen geometries. The geometry selected from the simulations achieves a simulated matching of −43 dB at 28 GHz, a 2.75 GHz bandwidth and a simulated gain of 4.4 dBi; the contribution of this work is not the antenna itself, which is a conventional benchmark. The fabricated prototype resonates at 28.07 GHz against 28.02 GHz in simulation, i.e., within 50 MHz (0.18%). The same full-factorial database (±100 µm around the fabricated design) shows that S11 at 28 GHz remains below −26 dB for every combination of deviations and that y1 is the geometrical parameter that most affects the resonance frequency, followed by x1, y2 and x2. A Bayesian inverse analysis based on the MLP shows, on a blind simulated test and on the measured curve, that S11 alone only partially identifies the individual deviations (only y1 is recovered, and the 90% intervals contain the true value in 50–67% of the cases). Moreover, additional ANSYS HFSS (version .13, Ansys Inc., Canonsburg, PA, USA) simulations show that a change of only −0.3% of the FR4 permittivity or −13 µm of its thickness reproduces the measured 50 MHz shift, whereas ±100 µm of any geometrical parameter shifts the resonance by at most ±40 MHz. The substrate therefore dominates over the geometrical deviations, and when a substrate nuisance parameter is included in the inverse analysis (approximate model), none of the four geometrical deviations is identified from S11. These results delimit what can and cannot be diagnosed from a single S11 measurement, and provide guidelines for the validation of fabricated mmWave antennas (direct dimensional measurements and substrate characterization).

ElectronicsVol. 15(22)
Tunis University (TN), University of Carthage (TN), Umm al-Qura University (SA), Tunisia Polytechnic School (TN), National Engineering School of Tunis (TN), Tunis El Manar University (TN)
Umm Al-Qura University
Antenna Design and Analysis
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon