Interface Bonding and Geometric Effects on Microsurfacing Performance of Low-Volume Roads in the Peruvian Highlands

Abstract Low-volume roads in mountainous regions often rely on economical pavement structures that are highly vulnerable to deterioration in horizontal curves. Conventional mechanistic–empirical design methods typically neglect horizontal forces, despite experimental and analytical evidence showing that lateral friction and braking significantly modify pavement response. This paper investigates the combined influence of horizontal curve geometry and interface bonding conditions on the structural performance of a microsurfacing over soil–cement base (MCP–BSC) pavement typical of low-volume roads in Peru. A three-dimensional finite-element model was developed in PLAXIS 3D and calibrated for a standard dual-wheel 80-kN axle. A total of 32 simulations were performed, varying design speed ( 20 – 60 km / h ), radius of curvature (15–125 m), and interface bonding coefficient ( R inter = 0.6 and 1.0). Horizontal forces were computed from equilibrium between centrifugal force, superelevation, and lateral friction and applied as tangential stresses at the tire–pavement contact patch. The mechanical response was characterized through transverse and longitudinal horizontal strains and interface shear stress, which were then transformed into equivalent axle loads using standard fatigue transfer functions. Results confirmed that horizontal forces generated by vehicle cornering substantially accelerate deterioration. For a representative case, adding horizontal loading reduced top-down fatigue life at the surface by up to 97% compared with vertical-only loading, in agreement with previous findings on near-surface multiaxial stress states. Interface debonding ( R inter = 0.6 ) decreased interface shear stress by 29% but increased surface horizontal strain by 13%, indicating loss of monolithic behavior and redistribution of demand to other layers. Multiple linear regression models relating equivalent axle loads to speed, radius, and bonding achieved R -squared values between 0.87 and 0.98. The most critical scenario, small radii ( R less than 25 m), high speeds ( V greater than 30 km / h ), and poor bonding, can reduce service life by up to 75%. The findings support explicit consideration of lateral friction effects and interface performance in pavement design for curved sections of low-volume roads.

Authors

Institutions

Publication Details

Journal
Journal of Transportation Engineering Part B Pavements
Published
2026-11-17
DOI
https://doi.org/10.1061/jpeodx.pveng-2180
Primary Topic
Asphalt Pavement Performance Evaluation
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Interface Bonding and Geometric Effects on Microsurfacing Performance of Low-Volume Roads in the Peruvian Highlands

Angel H. Vílchez Peña, Alex Ircañaupa, Víctor Bellido Aedo, Hemerson Lizarbe Alarcon et al.
2 links
Journal of Transportation Engineering Part B Pavements
Asphalt Pavement Performance Evaluation
article

Interface Bonding and Geometric Effects on Microsurfacing Performance of Low-Volume Roads in the Peruvian Highlands

Angel H. Vílchez Peña, Alex Ircañaupa, Víctor Bellido Aedo, Hemerson Lizarbe Alarcon, Jose Ernesto Estrada Cardenas, Bryan Tarik Urbina Gómez, Moises Nico Barbaran Oriundo
article en

Abstract

Abstract Low-volume roads in mountainous regions often rely on economical pavement structures that are highly vulnerable to deterioration in horizontal curves. Conventional mechanistic–empirical design methods typically neglect horizontal forces, despite experimental and analytical evidence showing that lateral friction and braking significantly modify pavement response. This paper investigates the combined influence of horizontal curve geometry and interface bonding conditions on the structural performance of a microsurfacing over soil–cement base (MCP–BSC) pavement typical of low-volume roads in Peru. A three-dimensional finite-element model was developed in PLAXIS 3D and calibrated for a standard dual-wheel 80-kN axle. A total of 32 simulations were performed, varying design speed ( 20 – 60 km / h ), radius of curvature (15–125 m), and interface bonding coefficient ( R inter = 0.6 and 1.0). Horizontal forces were computed from equilibrium between centrifugal force, superelevation, and lateral friction and applied as tangential stresses at the tire–pavement contact patch. The mechanical response was characterized through transverse and longitudinal horizontal strains and interface shear stress, which were then transformed into equivalent axle loads using standard fatigue transfer functions. Results confirmed that horizontal forces generated by vehicle cornering substantially accelerate deterioration. For a representative case, adding horizontal loading reduced top-down fatigue life at the surface by up to 97% compared with vertical-only loading, in agreement with previous findings on near-surface multiaxial stress states. Interface debonding ( R inter = 0.6 ) decreased interface shear stress by 29% but increased surface horizontal strain by 13%, indicating loss of monolithic behavior and redistribution of demand to other layers. Multiple linear regression models relating equivalent axle loads to speed, radius, and bonding achieved R -squared values between 0.87 and 0.98. The most critical scenario, small radii ( R less than 25 m), high speeds ( V greater than 30 km / h ), and poor bonding, can reduce service life by up to 75%. The findings support explicit consideration of lateral friction effects and interface performance in pavement design for curved sections of low-volume roads.

Journal of Transportation Engineering Part B PavementsVol. 153(1)
San Cristóbal of Huamanga University (PE)
Industry, innovation and infrastructure, Sustainable cities and communities
Asphalt Pavement Performance Evaluation
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon