Microstructural Inhomogeneity Complicates Small‐Scale Fracture Toughness Testing of Ceramic Nanocomposites

Ion‐implantation effects in ceramics and composites are surface‐localized to a few microns. Therefore, measurements of the mechanical properties, such as fracture toughness, of ion‐implanted ceramics and composites necessitate the use of microscopic specimens. While techniques such as microcantilever beam bending and micropillar splitting are often used to test microscopic specimens, critically comparing the results from these two techniques is important. Here, the micropillar splitting technique was used to measure the fracture toughness of monolithic SiC (1.94 ± 0.27 MPa·m 1/2 ) and carbon nanotubes (CNTs)‐reinforced SiC nanocomposites before and after C 2+ ion implantation. These results are compared with fracture toughness values previously measured for the same materials using the microcantilever beam bending technique. There is good agreement between the fracture toughness of monolithic SiC measured by micropillar splitting and microcantilever beam bending (~1.94 vs. ~2.42 MPa·m 1/2 , respectively, for the nonirradiated condition), as well as with literature values. However, the fracture toughness of the nanocomposites measured by the micropillar‐splitting technique was consistently lower than that obtained by microcantilever beam bending, both under nonirradiated conditions (~0.99 vs. ~2.70 MPa·m 1/2 , respectively) and after irradiation (~1.55 vs. ~4.76 MPa·m 1/2 , respectively). This difference was attributed to the pronounced microstructural inhomogeneity resulting from CNT addition and ion implantation.

Authors

Institutions

Publication Details

Journal
Advanced Engineering Materials
Published
2026-11-17
DOI
https://doi.org/10.1002/adem.71425
Primary Topic
Fusion materials and technologies
Type
article
Field-Weighted Citation Impact
0.00

Funders

Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Microstructural Inhomogeneity Complicates Small‐Scale Fracture Toughness Testing of Ceramic Nanocomposites

Aleksandar S. Mijailovic, Nitin P. Padture, Jun Lou, Izabela Szlufarska et al.
Advanced Engineering Materials
Fusion materials and technologies
article

Microstructural Inhomogeneity Complicates Small‐Scale Fracture Toughness Testing of Ceramic Nanocomposites

Aleksandar S. Mijailovic, Nitin P. Padture, Jun Lou, Izabela Szlufarska, Doug Steinbach, Cristina Ramírez, Brian W. Sheldon, Christos E. Athanasiou, Boyu Zhang, Xing Wang, Xing Liu, Rodolfo Cantu
article en

Abstract

Ion‐implantation effects in ceramics and composites are surface‐localized to a few microns. Therefore, measurements of the mechanical properties, such as fracture toughness, of ion‐implanted ceramics and composites necessitate the use of microscopic specimens. While techniques such as microcantilever beam bending and micropillar splitting are often used to test microscopic specimens, critically comparing the results from these two techniques is important. Here, the micropillar splitting technique was used to measure the fracture toughness of monolithic SiC (1.94 ± 0.27 MPa·m 1/2 ) and carbon nanotubes (CNTs)‐reinforced SiC nanocomposites before and after C 2+ ion implantation. These results are compared with fracture toughness values previously measured for the same materials using the microcantilever beam bending technique. There is good agreement between the fracture toughness of monolithic SiC measured by micropillar splitting and microcantilever beam bending (~1.94 vs. ~2.42 MPa·m 1/2 , respectively, for the nonirradiated condition), as well as with literature values. However, the fracture toughness of the nanocomposites measured by the micropillar‐splitting technique was consistently lower than that obtained by microcantilever beam bending, both under nonirradiated conditions (~0.99 vs. ~2.70 MPa·m 1/2 , respectively) and after irradiation (~1.55 vs. ~4.76 MPa·m 1/2 , respectively). This difference was attributed to the pronounced microstructural inhomogeneity resulting from CNT addition and ion implantation.

Advanced Engineering Materials
Northwestern University (US), New Jersey Institute of Technology (US), Georgia Institute of Technology (US), Pennsylvania State University (US), University of Wisconsin–Madison (US), Brown University (US), Rice University (US)
Basic Energy Sciences
Fusion materials and technologies
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon