Multi-Axis Design of Asymmetric Bilayer Nanocomposite PolyHIPEs for Interface Tissue Engineering

Abstract Spatially distinct requirements at tissue interfaces motivate scaffold designs that integrate regional differences into a single construct. Here, an asymmetric bilayer polymerized high internal phase emulsion (PolyHIPE) membrane was developed from photo-cross-linkable four-arm polycaprolactone methacrylate (4PCLMA) using coordinated molecular, formulation, and processing variables. The high-methacrylated network exhibited lower swelling in dichloromethane (133 ± 3% vs 159 ± 7%) and a higher compressive modulus (20.6 ± 4.2 MPa vs 6.6 ± 4.5 MPa) than the low-methacrylated network. For the bone-facing layer, 3 wt % nanohydroxyapatite increased pore diameter from 19 ± 10 to 28 ± 15 μm, compressive modulus from 0.28 ± 0.09 to 0.83 ± 0.24 MPa, and protein adsorption by 1.9-fold, while increasing human mesenchymal stem cell penetration relative to the nanohydroxyapatite-free formulation. For the soft-tissue-facing layer, increasing emulsification speed to 1000 rpm reduced pore diameter to 7 ± 4 μm without significantly altering stiffness. The selected layers differed 4-fold in pore diameter and approximately 14-fold in compressive modulus, with the latter determined over distinct strain intervals corresponding to their respective approximately linear regions. Consecutive casting and simultaneous photo-cross-linking produced a bilayer membrane that conformed to curved surfaces without visible delamination. Hydrated membranes exhibited a drape angle of 111.2 ± 2.3°, tensile modulus of 0.501 ± 0.008 MPa, ultimate tensile strength of 0.213 ± 0.042 MPa, and elongation at break of 37.4 ± 6.0%. Direct tensile testing of model co-photo-cross-linked specimens yielded an interfacial tensile strength of 0.093 ± 0.031 MPa. These findings demonstrate a coordinated strategy for generating spatially distinct properties within a PolyHIPE platform, highlighting its potential for selective tissue guidance at soft–hard tissue interfaces.

Authors

Institutions

Publication Details

Journal
ACS Applied Polymer Materials
Published
2026-11-17
DOI
https://doi.org/10.1021/acsapm.6c03230
Primary Topic
Bone Tissue Engineering Materials
Type
article
Field-Weighted Citation Impact
0.00

Funders

Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Multi-Axis Design of Asymmetric Bilayer Nanocomposite PolyHIPEs for Interface Tissue Engineering

Betül Aldemir Dikici, Oğul Can Erdoğan
1 links
ACS Applied Polymer Materials
Bone Tissue Engineering Materials
article

Multi-Axis Design of Asymmetric Bilayer Nanocomposite PolyHIPEs for Interface Tissue Engineering

Betül Aldemir Dikici, Oğul Can Erdoğan
article en

Abstract

Abstract Spatially distinct requirements at tissue interfaces motivate scaffold designs that integrate regional differences into a single construct. Here, an asymmetric bilayer polymerized high internal phase emulsion (PolyHIPE) membrane was developed from photo-cross-linkable four-arm polycaprolactone methacrylate (4PCLMA) using coordinated molecular, formulation, and processing variables. The high-methacrylated network exhibited lower swelling in dichloromethane (133 ± 3% vs 159 ± 7%) and a higher compressive modulus (20.6 ± 4.2 MPa vs 6.6 ± 4.5 MPa) than the low-methacrylated network. For the bone-facing layer, 3 wt % nanohydroxyapatite increased pore diameter from 19 ± 10 to 28 ± 15 μm, compressive modulus from 0.28 ± 0.09 to 0.83 ± 0.24 MPa, and protein adsorption by 1.9-fold, while increasing human mesenchymal stem cell penetration relative to the nanohydroxyapatite-free formulation. For the soft-tissue-facing layer, increasing emulsification speed to 1000 rpm reduced pore diameter to 7 ± 4 μm without significantly altering stiffness. The selected layers differed 4-fold in pore diameter and approximately 14-fold in compressive modulus, with the latter determined over distinct strain intervals corresponding to their respective approximately linear regions. Consecutive casting and simultaneous photo-cross-linking produced a bilayer membrane that conformed to curved surfaces without visible delamination. Hydrated membranes exhibited a drape angle of 111.2 ± 2.3°, tensile modulus of 0.501 ± 0.008 MPa, ultimate tensile strength of 0.213 ± 0.042 MPa, and elongation at break of 37.4 ± 6.0%. Direct tensile testing of model co-photo-cross-linked specimens yielded an interfacial tensile strength of 0.093 ± 0.031 MPa. These findings demonstrate a coordinated strategy for generating spatially distinct properties within a PolyHIPE platform, highlighting its potential for selective tissue guidance at soft–hard tissue interfaces.

ACS Applied Polymer Materials
Izmir Institute of Technology (TR)
Türkiye Bilimsel ve Teknolojik Araştırma Kurumu
Bone Tissue Engineering Materials
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon