Modeling and experimentation of carbon fiber tows and 3D-printed continuous carbon fiber-reinforced thermoplastic filaments under tensile stress

Continuous carbon fiber-reinforced thermoplastics (cCFRTPs) combine the high strength-to-weight ratio of carbon fiber with the design flexibility of fused-filament fabrication, but their performance is often limited by microstructural defects and fiber-matrix interface quality. In this work, we systematically evaluate the longitudinal Young’s modulus of both carbon fiber tows and fused deposition modeling (FDM) printed single-filament cCFRTPs using three common thermoplastic matrices (PLA, PETG, and CoPA). Specimens were tested in uniaxial tension according to the ASTM D4018 and ASTM C1557 standards, and a subset was subjected to a 6 hour vacuum-oven post-process to assess the effects of void reduction and residual-stress relief. Analytical predictions were obtained via Chamis’s criterion (for carbon fiber tow) and the Voigt-Reuss homogenization model, while numerical estimates employed finite-element RVEs with periodic boundary conditions in COMSOL Multiphysics. Carbon fiber tow specimens exhibited an experimental Young’s modulus of 122.5 ± 6.6GPa versus a Chamis prediction of 139.6GPa (6.3% error), compared to the manufacturer’s nominal 149±5GPa. For printed composites, vacuum-processing increased PLA+cCF Young’s modulus from 30.02±1.27GPa to 33.51±0.84GPa (11.6% gain) and PETG+cCF from 29.65±0.83GPa to 33.97±1.26GPa (14.6% gain), whereas CoPA+cCF decreased from 35.09 ± 1.50GPa to 29.88 ± 1.44GPa, likely due to moisture uptake in the hygroscopic nylon matrix. Both Voigt-Reuss and FE-RVE models consistently overpredicted the as-printed moduli by 10-12%, reflecting idealized assumptions of perfect alignment and zero porosity. Overall, simple homogenization and RVE approaches achieve computationally efficient optimization of 3D-printed cCFRTPs, with results accurate to an acceptable error range of 5-12%

Authors

Institutions

Publication Details

Journal
Transactions of the Canadian Society for Mechanical Engineering
Published
2026-11-16
DOI
https://doi.org/10.1139/tcsme-2026-0065
Primary Topic
Additive Manufacturing and 3D Printing Technologies
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Modeling and experimentation of carbon fiber tows and 3D-printed continuous carbon fiber-reinforced thermoplastic filaments under tensile stress

Kamran Behdinan, Victoria Velikonja
Transactions of the Canadian Society for Mechanical Engineering
Additive Manufacturing and 3D Printing Technologies
article

Modeling and experimentation of carbon fiber tows and 3D-printed continuous carbon fiber-reinforced thermoplastic filaments under tensile stress

Kamran Behdinan, Victoria Velikonja
article en

Abstract

Continuous carbon fiber-reinforced thermoplastics (cCFRTPs) combine the high strength-to-weight ratio of carbon fiber with the design flexibility of fused-filament fabrication, but their performance is often limited by microstructural defects and fiber-matrix interface quality. In this work, we systematically evaluate the longitudinal Young’s modulus of both carbon fiber tows and fused deposition modeling (FDM) printed single-filament cCFRTPs using three common thermoplastic matrices (PLA, PETG, and CoPA). Specimens were tested in uniaxial tension according to the ASTM D4018 and ASTM C1557 standards, and a subset was subjected to a 6 hour vacuum-oven post-process to assess the effects of void reduction and residual-stress relief. Analytical predictions were obtained via Chamis’s criterion (for carbon fiber tow) and the Voigt-Reuss homogenization model, while numerical estimates employed finite-element RVEs with periodic boundary conditions in COMSOL Multiphysics. Carbon fiber tow specimens exhibited an experimental Young’s modulus of 122.5 ± 6.6GPa versus a Chamis prediction of 139.6GPa (6.3% error), compared to the manufacturer’s nominal 149±5GPa. For printed composites, vacuum-processing increased PLA+cCF Young’s modulus from 30.02±1.27GPa to 33.51±0.84GPa (11.6% gain) and PETG+cCF from 29.65±0.83GPa to 33.97±1.26GPa (14.6% gain), whereas CoPA+cCF decreased from 35.09 ± 1.50GPa to 29.88 ± 1.44GPa, likely due to moisture uptake in the hygroscopic nylon matrix. Both Voigt-Reuss and FE-RVE models consistently overpredicted the as-printed moduli by 10-12%, reflecting idealized assumptions of perfect alignment and zero porosity. Overall, simple homogenization and RVE approaches achieve computationally efficient optimization of 3D-printed cCFRTPs, with results accurate to an acceptable error range of 5-12%

Transactions of the Canadian Society for Mechanical Engineering
University of Toronto (CA)
Additive Manufacturing and 3D Printing Technologies
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon