Research on the vibration characteristics during rock-breaking process by microwave and cutter under different microwave irradiation parameters

Tunnel excavation in extremely hard rock often causes severe vibration during the rock-breaking process. This vibration easily leads to cutter failure. Microwave-assisted cutter rock breaking is a research method. It is used to explore ways to improve the rock-breaking performance of cutters. This study explores the impact of microwave irradiation parameters on the vibration characteristics and energy efficiency of TBM cutter rock breaking. The research adopts a composite rock-breaking experimental method. This method combines microwave pretreatment and a scaled cutter. The rock specimen is granite. This granite has a compressive strength of 172.3 MPa. The experiment sets the penetration at 5 mm. It sets the cutter spacing at 35 mm. For granite with a compressive strength of 172.3 MPa, this study first analyzed the variation in compressive strength after microwave irradiation. Combined with the fragmentation state of the rock surface during the rock-breaking process, this study further analyzed the time-domain and frequency-domain characteristics of the original vibration signals after cutter rock breaking. This study introduced a total rock-breaking specific energy index. The index included the cutter cutting specific energy and microwave energy consumption. This study evaluated the trade-off between vibration suppression and rock-breaking energy efficiency. A dimensionless comprehensive evaluation index was established to optimize the microwave parameters. The experimental results show that after microwave irradiation, a high-temperature region forms on the rock specimen surface around the area corresponding to the waveguide port. The peak surface temperature increases significantly with increasing microwave power and irradiation time. When the irradiation time is 5 min, the average compressive strength of granite decreases from 172.36 MPa in the control group to 161.64, 146.97, and 126.17 MPa under microwave powers of 1, 2, and 3 kW, respectively. These results indicate that microwave pretreatment can effectively assist TBM cutter rock breaking and further reduce the rock strength. Overall, the vibration intensity of the cutter decreases with increasing microwave power and irradiation time.Under the 3 kW-15 min treatment condition, the peak acceleration and root-mean-square (RMS) value of cutter vibration decrease by 58.28% and 78.04%, respectively, compared with those during pure cutter rock breaking. The peak instantaneous equivalent vibration intensity decreases from 183.97 to 31.98. This condition achieves the best vibration suppression effect for the cutter and cutter housing system. However, its total rock-breaking specific energy reaches 228.14 MJ/m 3 , indicating poor economic performance. Another experimental group used microwave irradiation parameters of 3 kW for 5 min. The total rock-breaking specific energy of this group is 135.33 MJ/m 3 . Its vibration reduction effect on the cutter and cutter housing system is weaker than the 15-min group. However, it has higher economic efficiency. Therefore, the analysis combines vibration characteristics and total rock-breaking specific energy. It reveals a clear conclusion. Simply pursuing the best vibration reduction causes a sharp increase in total rock-breaking specific energy. Actual projects have different needs. Engineers should maintain a high microwave power. Under this condition, they can choose a suitable irradiation time. This choice effectively balances the vibration reduction effect and economic efficiency.

Authors

Institutions

Publication Details

Journal
Journal of low frequency noise, vibration and active control
Published
2026-11-16
DOI
https://doi.org/10.1177/14613484261506673
Primary Topic
Tunneling and Rock Mechanics
Type
article
Field-Weighted Citation Impact
0.00

Funders

Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Research on the vibration characteristics during rock-breaking process by microwave and cutter under different microwave irradiation parameters

Mei Yang, Huan Zeng, Yimin Xia, Bo Ning et al.
3 links
Journal of low frequency noise, vibration and active control
Tunneling and Rock Mechanics
article

Research on the vibration characteristics during rock-breaking process by microwave and cutter under different microwave irradiation parameters

Mei Yang, Huan Zeng, Yimin Xia, Bo Ning, Shuaichao Zheng, Dongshen Li
article en

Abstract

Tunnel excavation in extremely hard rock often causes severe vibration during the rock-breaking process. This vibration easily leads to cutter failure. Microwave-assisted cutter rock breaking is a research method. It is used to explore ways to improve the rock-breaking performance of cutters. This study explores the impact of microwave irradiation parameters on the vibration characteristics and energy efficiency of TBM cutter rock breaking. The research adopts a composite rock-breaking experimental method. This method combines microwave pretreatment and a scaled cutter. The rock specimen is granite. This granite has a compressive strength of 172.3 MPa. The experiment sets the penetration at 5 mm. It sets the cutter spacing at 35 mm. For granite with a compressive strength of 172.3 MPa, this study first analyzed the variation in compressive strength after microwave irradiation. Combined with the fragmentation state of the rock surface during the rock-breaking process, this study further analyzed the time-domain and frequency-domain characteristics of the original vibration signals after cutter rock breaking. This study introduced a total rock-breaking specific energy index. The index included the cutter cutting specific energy and microwave energy consumption. This study evaluated the trade-off between vibration suppression and rock-breaking energy efficiency. A dimensionless comprehensive evaluation index was established to optimize the microwave parameters. The experimental results show that after microwave irradiation, a high-temperature region forms on the rock specimen surface around the area corresponding to the waveguide port. The peak surface temperature increases significantly with increasing microwave power and irradiation time. When the irradiation time is 5 min, the average compressive strength of granite decreases from 172.36 MPa in the control group to 161.64, 146.97, and 126.17 MPa under microwave powers of 1, 2, and 3 kW, respectively. These results indicate that microwave pretreatment can effectively assist TBM cutter rock breaking and further reduce the rock strength. Overall, the vibration intensity of the cutter decreases with increasing microwave power and irradiation time.Under the 3 kW-15 min treatment condition, the peak acceleration and root-mean-square (RMS) value of cutter vibration decrease by 58.28% and 78.04%, respectively, compared with those during pure cutter rock breaking. The peak instantaneous equivalent vibration intensity decreases from 183.97 to 31.98. This condition achieves the best vibration suppression effect for the cutter and cutter housing system. However, its total rock-breaking specific energy reaches 228.14 MJ/m 3 , indicating poor economic performance. Another experimental group used microwave irradiation parameters of 3 kW for 5 min. The total rock-breaking specific energy of this group is 135.33 MJ/m 3 . Its vibration reduction effect on the cutter and cutter housing system is weaker than the 15-min group. However, it has higher economic efficiency. Therefore, the analysis combines vibration characteristics and total rock-breaking specific energy. It reveals a clear conclusion. Simply pursuing the best vibration reduction causes a sharp increase in total rock-breaking specific energy. Actual projects have different needs. Engineers should maintain a high microwave power. Under this condition, they can choose a suitable irradiation time. This choice effectively balances the vibration reduction effect and economic efficiency.

Journal of low frequency noise, vibration and active control
Central South University (CN), Guangzhou University (CN), China Railway Group (China) (CN)
Natural Science Foundation of Nantong City, National Natural Science Foundation of China, Basic and Applied Basic Research Foundation of Guangdong Province
Industry, innovation and infrastructure
Tunneling and Rock Mechanics
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon