Subtransus thermal route selection and constitutive assessment for Heat Stamping Ti-6Al-4V sheet

Separating the soaking and deformation temperatures provides a means of tailoring the elevated-temperature response of Ti-6Al-4V sheet before rapid forming. Direct-heating (DH) and step-quenching (SQ) tensile responses were compared at subtransus temperatures and nominal strain rates of 0.1, 1 and 5 s-1. SQ from 950 °C reduced the flow stress relative to DH at the same deformation temperature, but its effect on hardening and softening was strongly rate dependent. The 950→800 °C route exhibited prolonged hardening at 0.1 s-1 while retaining substantial softening at 5 s-1. A 900→850 °C route provided a more balanced response, combining a lower flow stress than DH850 °C with reduced softening and positive apparent rate dependence. Post-test microscopy showed route- and rate-dependent α morphologies and image-derived α fractions consistent with the different thermal exposures and deformation times. A thermal-history-dependent constitutive formulation based on the Gavrus mixture framework was calibrated using the DH and 950 °C-based SQ datasets and subsequently assessed against the 900→850 °C route, capturing the principal stress, strain and rate trends over the calibrated strain range. A previously demonstrated cup with 1.8 draw ratio formed using the 900→850 °C route was further assessed at component level. The maximum measured thickness reduction was 12.7% near the punch corner. The simulation reproduced the overall thickness-profile trend and predicted considerable spatial variations in equivalent plastic strain and temperature during the 0.38 s draw. Post-form microscopy showed corresponding spatial changes in primary α morphology. The results identify the SQ900→850 °C route as a practical compromise within the tested matrix and demonstrate the importance of thermal history alongside instantaneous forming temperature and strain rate.

Authors

Institutions

Publication Details

Journal
Engineering Archive (engrXiv)
Published
2026-11-16
DOI
https://doi.org/10.31224/8809
Primary Topic
Metallurgy and Material Forming
Type
preprint

Funders

Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
preprint

Subtransus thermal route selection and constitutive assessment for Heat Stamping Ti-6Al-4V sheet

Famin Tian, Hao Wu, Nan Li
1 links
Engineering Archive (engrXiv)
Metallurgy and Material Forming
preprint

Subtransus thermal route selection and constitutive assessment for Heat Stamping Ti-6Al-4V sheet

Famin Tian, Hao Wu, Nan Li
preprint en

Abstract

Separating the soaking and deformation temperatures provides a means of tailoring the elevated-temperature response of Ti-6Al-4V sheet before rapid forming. Direct-heating (DH) and step-quenching (SQ) tensile responses were compared at subtransus temperatures and nominal strain rates of 0.1, 1 and 5 s-1. SQ from 950 °C reduced the flow stress relative to DH at the same deformation temperature, but its effect on hardening and softening was strongly rate dependent. The 950→800 °C route exhibited prolonged hardening at 0.1 s-1 while retaining substantial softening at 5 s-1. A 900→850 °C route provided a more balanced response, combining a lower flow stress than DH850 °C with reduced softening and positive apparent rate dependence. Post-test microscopy showed route- and rate-dependent α morphologies and image-derived α fractions consistent with the different thermal exposures and deformation times. A thermal-history-dependent constitutive formulation based on the Gavrus mixture framework was calibrated using the DH and 950 °C-based SQ datasets and subsequently assessed against the 900→850 °C route, capturing the principal stress, strain and rate trends over the calibrated strain range. A previously demonstrated cup with 1.8 draw ratio formed using the 900→850 °C route was further assessed at component level. The maximum measured thickness reduction was 12.7% near the punch corner. The simulation reproduced the overall thickness-profile trend and predicted considerable spatial variations in equivalent plastic strain and temperature during the 0.38 s draw. Post-form microscopy showed corresponding spatial changes in primary α morphology. The results identify the SQ900→850 °C route as a practical compromise within the tested matrix and demonstrate the importance of thermal history alongside instantaneous forming temperature and strain rate.

Engineering Archive (engrXiv)
Imperial College London (GB)
UK Research and Innovation, Imperial College London, Engineering and Physical Sciences Research Council
Metallurgy and Material Forming
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon