Evaluation of the potential and mitigation strategies of post-liquefaction residual deformations in heterogeneous fill soils through performance-based parametric simulations

Assessments of liquefaction hazards in heterogeneous reclaimed soils are often limited to safety factor-based triggering analyses (FSliq) without considering the consequences of post-earthquake residual deformation. This study aims to evaluate the reliability of FSliq as a single indicator for representing permanent deformation response, as well as to determine the optimal performance-based design threshold for soil improvement. The analysis is based on ten CPTu soundings reported in previous study from the Pantai Indah Kapuk land reclamation area, North Jakarta, evaluated under the Cimandiri Fault earthquake scenario (Mw 6.7). Residual deformation estimates were calculated using semi-empirical vertical and horizontal approaches. The results of the baseline analysis indicate significant vulnerability in the 4.0–10.5 m layer, where FSliq < 1.0, which could trigger vertical settlement of up to 26.02 cm and lateral displacement of up to 300.52 cm. Parametric simulations of three remediation scenarios (light, moderate, and intensive) detected fluctuations in negative Deformation Reduction Ratio (DRR) values at local 0.5-meter intervals in Scenario 1 (light). This phenomenon was validated as a physical manifestation of the boundary sensitivity state, where minor reinforcement – which was insufficient to bring the FSliq value out of the critical zone (FSliq ≤ 0.5) – triggered a transient strain spike. The cumulative nonlinear regression plot of the entire profile clearly confirms the point of diminishing returns in engineering efficiency following Scenario 2 (Moderate). The moderate improvement target, with an average profile strength of qc ~ 13.85 MPa is considered the most recommended design criterion because it effectively limits deformation to safe allowable limits with DRRSett ≈ 80.24% and DRRLD ≈ 88.80% without requiring a high level of construction energy waste in Scenario 3.

Authors

Institutions

Publication Details

Journal
Derbyana
Published
2026-11-16
DOI
https://doi.org/10.69469/derb.v47.920
Primary Topic
Geotechnical Engineering and Soil Mechanics
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Evaluation of the potential and mitigation strategies of post-liquefaction residual deformations in heterogeneous fill soils through performance-based parametric simulations

Hendra Pachri, Erfandi Rahman, Busthan Azikin
Derbyana
Geotechnical Engineering and Soil Mechanics
article

Evaluation of the potential and mitigation strategies of post-liquefaction residual deformations in heterogeneous fill soils through performance-based parametric simulations

Hendra Pachri, Erfandi Rahman, Busthan Azikin
article en

Abstract

Assessments of liquefaction hazards in heterogeneous reclaimed soils are often limited to safety factor-based triggering analyses (FSliq) without considering the consequences of post-earthquake residual deformation. This study aims to evaluate the reliability of FSliq as a single indicator for representing permanent deformation response, as well as to determine the optimal performance-based design threshold for soil improvement. The analysis is based on ten CPTu soundings reported in previous study from the Pantai Indah Kapuk land reclamation area, North Jakarta, evaluated under the Cimandiri Fault earthquake scenario (Mw 6.7). Residual deformation estimates were calculated using semi-empirical vertical and horizontal approaches. The results of the baseline analysis indicate significant vulnerability in the 4.0–10.5 m layer, where FSliq < 1.0, which could trigger vertical settlement of up to 26.02 cm and lateral displacement of up to 300.52 cm. Parametric simulations of three remediation scenarios (light, moderate, and intensive) detected fluctuations in negative Deformation Reduction Ratio (DRR) values at local 0.5-meter intervals in Scenario 1 (light). This phenomenon was validated as a physical manifestation of the boundary sensitivity state, where minor reinforcement – which was insufficient to bring the FSliq value out of the critical zone (FSliq ≤ 0.5) – triggered a transient strain spike. The cumulative nonlinear regression plot of the entire profile clearly confirms the point of diminishing returns in engineering efficiency following Scenario 2 (Moderate). The moderate improvement target, with an average profile strength of qc ~ 13.85 MPa is considered the most recommended design criterion because it effectively limits deformation to safe allowable limits with DRRSett ≈ 80.24% and DRRLD ≈ 88.80% without requiring a high level of construction energy waste in Scenario 3.

DerbyanaVol. 47
Hasanuddin University (ID)
Sustainable cities and communities
Geotechnical Engineering and Soil Mechanics
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon