A voxel-based numerical approach to predict dimensional deviations in ABS parts manufactured by material extrusion

Purpose This study aims to propose and experimentally validate a voxel-based numerical procedure for predicting dimensional deviations in acrylonitrile butadiene styrene (ABS) parts manufactured by material extrusion. Design/methodology/approach The workflow combines finite-element simulation of the printing process with virtual inspection of the resulting geometry. A benchmark part, including external surfaces, circular holes, rectangular pockets and a square pocket, was manufactured, measured with a coordinate-measuring machine and compared with numerical predictions. A voxel-size sensitivity analysis was performed by varying the voxel size from 0.4 to 2.0 mm. Findings Experimental deviations from nominal dimensions ranged from −2.08% to −0.02%, confirming the tendency of ABS parts to shrink. For the finest voxel size, numerical–experimental differences ranged from −1.15% to 1.99%, and 8 out of 10 measured dimensions showed absolute errors below 0.25 mm. The 0.4 mm voxel size yielded the lowest mean absolute error (0.22 mm), but required approximately four times the computational time of the 2.0 mm configuration. Intermediate voxel sizes, especially 1.2 and 1.6 mm, showed slightly higher errors but lower computational cost. Research limitations/implications This voxel-based approach was validated only for ABS parts via material extrusion. An isotropic material formulation and simplified thermal boundary conditions were adopted. Therefore, the process-induced anisotropy of the printed ABS component was not explicitly calibrated. Future work should include direction-dependent material characterisation and validation across different geometries and printing conditions. Future work will test complex geometries and temperature-dependent properties. The study provides evidence that voxel-based simulations can support dimensional prediction in MEX, though further validation across different materials, geometries, printers and process conditions is required. Practical implications This numerical tool can help industrial practitioners predict dimensional deviations in material extrusion parts prior to printing. The workflow provides practical guidance for selecting voxel resolution by balancing prediction accuracy, feature complexity and computational cost. Originality/value The individual finite element, voxel-discretisation and virtual-inspection methods are established. The originality of this study lies in its integration within a metrology-oriented workflow that compares simulated and CMM-measured geometries using equivalent feature-reconstruction criteria. Rather than merely confirming that smaller voxels improve geometrical representation, this study demonstrates that the resulting improvement in dimensional prediction is feature-dependent and may be non-monotonic. Within the investigated material, benchmark geometry, printer and process conditions, the results provide preliminary guidance for voxel-resolution selection by illustrating the trade-off between feature-level accuracy and computational cost.

Authors

Institutions

Publication Details

Journal
Rapid Prototyping Journal
Published
2026-11-16
DOI
https://doi.org/10.1108/rpj-05-2026-0334
Primary Topic
Additive Manufacturing and 3D Printing Technologies
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

A voxel-based numerical approach to predict dimensional deviations in ABS parts manufactured by material extrusion

Valentina Vendittoli, Wilma Polini, Michael S. J. Walter
Rapid Prototyping Journal
Additive Manufacturing and 3D Printing Technologies
article

A voxel-based numerical approach to predict dimensional deviations in ABS parts manufactured by material extrusion

Valentina Vendittoli, Wilma Polini, Michael S. J. Walter
article en

Abstract

Purpose This study aims to propose and experimentally validate a voxel-based numerical procedure for predicting dimensional deviations in acrylonitrile butadiene styrene (ABS) parts manufactured by material extrusion. Design/methodology/approach The workflow combines finite-element simulation of the printing process with virtual inspection of the resulting geometry. A benchmark part, including external surfaces, circular holes, rectangular pockets and a square pocket, was manufactured, measured with a coordinate-measuring machine and compared with numerical predictions. A voxel-size sensitivity analysis was performed by varying the voxel size from 0.4 to 2.0 mm. Findings Experimental deviations from nominal dimensions ranged from −2.08% to −0.02%, confirming the tendency of ABS parts to shrink. For the finest voxel size, numerical–experimental differences ranged from −1.15% to 1.99%, and 8 out of 10 measured dimensions showed absolute errors below 0.25 mm. The 0.4 mm voxel size yielded the lowest mean absolute error (0.22 mm), but required approximately four times the computational time of the 2.0 mm configuration. Intermediate voxel sizes, especially 1.2 and 1.6 mm, showed slightly higher errors but lower computational cost. Research limitations/implications This voxel-based approach was validated only for ABS parts via material extrusion. An isotropic material formulation and simplified thermal boundary conditions were adopted. Therefore, the process-induced anisotropy of the printed ABS component was not explicitly calibrated. Future work should include direction-dependent material characterisation and validation across different geometries and printing conditions. Future work will test complex geometries and temperature-dependent properties. The study provides evidence that voxel-based simulations can support dimensional prediction in MEX, though further validation across different materials, geometries, printers and process conditions is required. Practical implications This numerical tool can help industrial practitioners predict dimensional deviations in material extrusion parts prior to printing. The workflow provides practical guidance for selecting voxel resolution by balancing prediction accuracy, feature complexity and computational cost. Originality/value The individual finite element, voxel-discretisation and virtual-inspection methods are established. The originality of this study lies in its integration within a metrology-oriented workflow that compares simulated and CMM-measured geometries using equivalent feature-reconstruction criteria. Rather than merely confirming that smaller voxels improve geometrical representation, this study demonstrates that the resulting improvement in dimensional prediction is feature-dependent and may be non-monotonic. Within the investigated material, benchmark geometry, printer and process conditions, the results provide preliminary guidance for voxel-resolution selection by illustrating the trade-off between feature-level accuracy and computational cost.

Rapid Prototyping Journal
Università degli studi di Cassino e del Lazio Meridionale (IT), Ansbach University of Applied Sciences (DE)
Additive Manufacturing and 3D Printing Technologies
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon