Comparative microstructural and tribological assessment of friction-surfaced inconel 600 and inconel 718 overlays on H13 hot-work tool steel

The present study examines Inconel 600 and Inconel 718 coatings deposited on H13 hot-work tool steel by friction surfacing (FS). The coatings were evaluated in terms of cross-sectional morphology, phase constitution, interfacial composition, bond strength, microhardness, and dry-sliding wear. Both deposits formed continuous coating layers in the examined cross-sections, with no large interfacial gaps or delamination. The optical and SEM observations revealed differences in the apparent microstructural features of the two coatings, with distinct morphological characteristics observed in the Inconel 600 and Inconel 718 deposits. XRD patterns from both coatings were dominated by the γ-FCC Ni-based matrix; no additional secondary phase could be assigned with confidence from the presented diffraction patterns alone. EDS line scans showed gradual Fe–Ni–Cr compositional changes across the coating/substrate regions, while localized Nb and Mo enrichment was detected in the Inconel 718 deposit. The measured ram tensile bond strengths were 149 ± 4.2 MPa for Inconel 600 and 158 ± 3.9 MPa for Inconel 718. The coating hardness values were 389.0 ± 3.4 HV for Inconel 600 and 411.0 ± 3.1 HV for Inconel 718. Compared with the H13 substrate hardness of 442.0 ± 2.4 HV, both coatings had lower hardness, although Inconel 718 was harder than Inconel 600. Under dry sliding at 20–60 N, both coatings showed lower mass loss and specific wear rate than uncoated H13, and Inconel 718 exhibited the lowest values among the three tested surfaces. The worn-surface SEM images showed deeper grooves, delamination and adhesive damage on H13, whereas the coatings exhibited less severe surface damage, with localized oxidation and shallower grooves. Under the conditions examined, friction surfacing supports manufacturing innovation by producing nickel-based coatings on H13 tool steel, with Inconel 718 exhibiting the most favourable overall combination of measured bond strength, hardness relative to Inconel 600, and wear performance.

Authors

Institutions

Publication Details

Journal
Materials Today Communications
Published
2026-11-16
DOI
https://doi.org/10.1016/j.mtcomm.2026.116658
Primary Topic
Advanced Welding Techniques Analysis
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Comparative microstructural and tribological assessment of friction-surfaced inconel 600 and inconel 718 overlays on H13 hot-work tool steel

Manu Sam, Yuli Panca Asmara, B. Loveswara Rao, M Krishna et al.
Materials Today Communications
Advanced Welding Techniques Analysis
article

Comparative microstructural and tribological assessment of friction-surfaced inconel 600 and inconel 718 overlays on H13 hot-work tool steel

Manu Sam, Yuli Panca Asmara, B. Loveswara Rao, M Krishna, Suresh, S Vinodh
article en

Abstract

The present study examines Inconel 600 and Inconel 718 coatings deposited on H13 hot-work tool steel by friction surfacing (FS). The coatings were evaluated in terms of cross-sectional morphology, phase constitution, interfacial composition, bond strength, microhardness, and dry-sliding wear. Both deposits formed continuous coating layers in the examined cross-sections, with no large interfacial gaps or delamination. The optical and SEM observations revealed differences in the apparent microstructural features of the two coatings, with distinct morphological characteristics observed in the Inconel 600 and Inconel 718 deposits. XRD patterns from both coatings were dominated by the γ-FCC Ni-based matrix; no additional secondary phase could be assigned with confidence from the presented diffraction patterns alone. EDS line scans showed gradual Fe–Ni–Cr compositional changes across the coating/substrate regions, while localized Nb and Mo enrichment was detected in the Inconel 718 deposit. The measured ram tensile bond strengths were 149 ± 4.2 MPa for Inconel 600 and 158 ± 3.9 MPa for Inconel 718. The coating hardness values were 389.0 ± 3.4 HV for Inconel 600 and 411.0 ± 3.1 HV for Inconel 718. Compared with the H13 substrate hardness of 442.0 ± 2.4 HV, both coatings had lower hardness, although Inconel 718 was harder than Inconel 600. Under dry sliding at 20–60 N, both coatings showed lower mass loss and specific wear rate than uncoated H13, and Inconel 718 exhibited the lowest values among the three tested surfaces. The worn-surface SEM images showed deeper grooves, delamination and adhesive damage on H13, whereas the coatings exhibited less severe surface damage, with localized oxidation and shallower grooves. Under the conditions examined, friction surfacing supports manufacturing innovation by producing nickel-based coatings on H13 tool steel, with Inconel 718 exhibiting the most favourable overall combination of measured bond strength, hardness relative to Inconel 600, and wear performance.

Materials Today CommunicationsVol. 57
INTI International University (MY), Curtin University (AU), Rathinam Technical Campus (IN), Koneru Lakshmaiah Education Foundation (IN)
Advanced Welding Techniques Analysis
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon