Physicochemical and biological evaluation of hardystonite-reinforced Poly(ε-caprolactone) composite membranes for guided bone regeneration applications

The development of bioactive and biodegradable barrier membranes is essential for successful guided bone regeneration (GBR). Poly(ε-caprolactone) (PCL) is widely used in GBR applications; however, its limited bioactivity and hydrophobicity limit its regenerative potential. This study aimed to fabricate and characterize hardystonite (HT)-reinforced PCL composite membranes and evaluate their physicochemical, biological, and antibacterial properties for GBR applications. Composite membranes containing 0, 1, 3, and 5 wt% HT were fabricated using a solvent-casting/freeze-drying approach. The membranes were characterized by FTIR, XRD, SEM/EDX, contact angle measurements, mechanical testing, degradation analysis, ion release studies, antibacterial assessment, and cytocompatibility evaluation. Bioactivity was investigated through immersion in simulated body fluid (SBF) for up to 28 days. Successful incorporation of crystalline HT nanoparticles into the PCL matrix was confirmed by FTIR and XRD analyses. HT addition increased membrane porosity and improved surface wettability, reducing the water contact angle from approximately 88° for pure PCL to 72° for the 5 wt% HT group. Mechanical reinforcement was observed, with elastic modulus increasing from 285 ± 32 kPa to 682 ± 58 kPa as HT content increased from 0 to 5 wt%. HT-containing membranes exhibited enhanced buffering capacity during degradation and showed higher mass loss after 28 days (16.2 ± 0.6% for 5 wt% HT versus 9.8 ± 0.7% for pure PCL). In vitro bioactivity analyses demonstrated concentration-dependent apatite formation, with the strongest mineral deposition observed in the 5 wt% HT group. Ion release studies revealed sustained release of Si and Zn ions accompanied by progressive consumption of Ca and P ions from SBF, indicating active mineralization. Furthermore, HT incorporation improved antibacterial activity against Staphylococcus aureus and Escherichia coli, with inhibition zones reaching 10.2 ± 1.1 mm and 8.8 ± 0.9 mm, respectively, for the 5 wt% HT membrane. All membranes maintained acceptable cytocompatibility, with cell viability remaining above 79% after 24 h exposure. HT-reinforced PCL membranes exhibited enhanced hydrophilicity, mechanical performance, antibacterial activity, and in vitro bioactivity while maintaining acceptable cytocompatibility. Among the investigated formulations, the membrane containing 5 wt% HT demonstrated the most favorable overall performance. Based on the evaluated in vitro properties, supporting its potential for further investigation as a GBR membrane for bone regeneration applications.

Authors

Institutions

Publication Details

Journal
BMC Oral Health
Published
2026-11-16
DOI
https://doi.org/10.1186/s12903-026-10425-z
Primary Topic
Bone Tissue Engineering Materials
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Physicochemical and biological evaluation of hardystonite-reinforced Poly(ε-caprolactone) composite membranes for guided bone regeneration applications

Hanieh Nojehdehian, Behzad Houshmand, Zahra Namazi, Maryam Torshabi et al.
1 links
BMC Oral Health
Bone Tissue Engineering Materials
article

Physicochemical and biological evaluation of hardystonite-reinforced Poly(ε-caprolactone) composite membranes for guided bone regeneration applications

Hanieh Nojehdehian, Behzad Houshmand, Zahra Namazi, Maryam Torshabi, Zahra Keshavarz
article en

Abstract

The development of bioactive and biodegradable barrier membranes is essential for successful guided bone regeneration (GBR). Poly(ε-caprolactone) (PCL) is widely used in GBR applications; however, its limited bioactivity and hydrophobicity limit its regenerative potential. This study aimed to fabricate and characterize hardystonite (HT)-reinforced PCL composite membranes and evaluate their physicochemical, biological, and antibacterial properties for GBR applications. Composite membranes containing 0, 1, 3, and 5 wt% HT were fabricated using a solvent-casting/freeze-drying approach. The membranes were characterized by FTIR, XRD, SEM/EDX, contact angle measurements, mechanical testing, degradation analysis, ion release studies, antibacterial assessment, and cytocompatibility evaluation. Bioactivity was investigated through immersion in simulated body fluid (SBF) for up to 28 days. Successful incorporation of crystalline HT nanoparticles into the PCL matrix was confirmed by FTIR and XRD analyses. HT addition increased membrane porosity and improved surface wettability, reducing the water contact angle from approximately 88° for pure PCL to 72° for the 5 wt% HT group. Mechanical reinforcement was observed, with elastic modulus increasing from 285 ± 32 kPa to 682 ± 58 kPa as HT content increased from 0 to 5 wt%. HT-containing membranes exhibited enhanced buffering capacity during degradation and showed higher mass loss after 28 days (16.2 ± 0.6% for 5 wt% HT versus 9.8 ± 0.7% for pure PCL). In vitro bioactivity analyses demonstrated concentration-dependent apatite formation, with the strongest mineral deposition observed in the 5 wt% HT group. Ion release studies revealed sustained release of Si and Zn ions accompanied by progressive consumption of Ca and P ions from SBF, indicating active mineralization. Furthermore, HT incorporation improved antibacterial activity against Staphylococcus aureus and Escherichia coli, with inhibition zones reaching 10.2 ± 1.1 mm and 8.8 ± 0.9 mm, respectively, for the 5 wt% HT membrane. All membranes maintained acceptable cytocompatibility, with cell viability remaining above 79% after 24 h exposure. HT-reinforced PCL membranes exhibited enhanced hydrophilicity, mechanical performance, antibacterial activity, and in vitro bioactivity while maintaining acceptable cytocompatibility. Among the investigated formulations, the membrane containing 5 wt% HT demonstrated the most favorable overall performance. Based on the evaluated in vitro properties, supporting its potential for further investigation as a GBR membrane for bone regeneration applications.

BMC Oral Health
Shahid Beheshti University (IR), Shahid Beheshti University of Medical Sciences (IR)
Good health and well-being
Bone Tissue Engineering Materials
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon