ANALISIS DISTRIBUSI TEGANGAN PADA SAMBUNGAN PIPA HIGH PRESSURE AKIBAT PENAMBAHAN STIFFENER MENGGUNAKAN ANSYS

High-pressure piping flange connections are susceptible to stress concentration due to geometric discontinuities, which may affect structural integrity. This study aims to analyze stress distribution and evaluate the effects of variations in the number and thickness of stiffener plates on Von Mises stress, stress concentration factor (SCF), and deformation in an ASME B16.5 Class 900 NPS 6 weld neck flange made of ASTM A105 steel. The study employed the finite element method using the Static Structural module in ANSYS Workbench, with an internal pressure of 15.3 MPa and a bolt pretension of 50% of the bolt yield strength. Six configurations were analyzed, consisting of one unreinforced model and five stiffener variations. The simulation results showed reductions in maximum stress of 9.31–15.87% and deformation of 22.24–25.60% compared with the unreinforced configuration. The configuration with eight 12-mm-thick stiffeners produced the lowest maximum stress of 202.47 MPa, whereas the configuration with twelve 4-mm-thick stiffeners achieved the highest reinforcement efficiency index. However, the mesh convergence study indicated that numerical stability had not been consistently achieved. Therefore, comparisons among configurations remain preliminary and require further numerical investigation. ABSTRAK Sambungan flange pada sistem perpipaan bertekanan tinggi rentan mengalami konsentrasi tegangan akibat diskontinuitas geometri yang dapat memengaruhi integritas struktural. Penelitian ini bertujuan menganalisis distribusi tegangan serta mengevaluasi pengaruh variasi jumlah dan ketebalan stiffener plate terhadap tegangan Von Mises, faktor konsentrasi tegangan (SCF), dan deformasi pada weld neck flange ASME B16.5 Class 900 NPS 6 berbahan ASTM A105. Penelitian menggunakan metode elemen hingga melalui ANSYS Workbench modul Static Structural dengan tekanan internal 15,3 MPa dan prategangan baut sebesar 50% tegangan luluh baut. Enam konfigurasi dianalisis, meliputi satu model tanpa penguatan dan lima variasi stiffener. Hasil simulasi menunjukkan penurunan tegangan maksimum sebesar 9,31–15,87% dan deformasi sebesar 22,24–25,60% dibandingkan konfigurasi tanpa penguatan. Konfigurasi delapan stiffener setebal 12 mm menghasilkan tegangan maksimum terendah sebesar 202,47 MPa, sedangkan konfigurasi dua belas stiffener setebal 4 mm menghasilkan indeks efisiensi penguatan tertinggi. Namun, hasil studi konvergensi mesh menunjukkan bahwa kestabilan numerik belum terpenuhi secara konsisten. Oleh karena itu, hasil perbandingan konfigurasi masih bersifat sementara dan memerlukan pengujian numerik lanjutan.

Authors

Institutions

Publication Details

Journal
KNOWLEDGE Jurnal Inovasi Hasil Penelitian dan Pengembangan
Published
2026-11-15
DOI
https://doi.org/10.51878/knowledge.v6i4.16888
Primary Topic
Engineering Structural Analysis Methods
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

ANALISIS DISTRIBUSI TEGANGAN PADA SAMBUNGAN PIPA HIGH PRESSURE AKIBAT PENAMBAHAN STIFFENER MENGGUNAKAN ANSYS

Delima Yanti Sari, Wanda Afnison, Waskito, Ridho Ogarbel Putera
KNOWLEDGE Jurnal Inovasi Hasil Penelitian dan Pengembangan
Engineering Structural Analysis Methods
article

ANALISIS DISTRIBUSI TEGANGAN PADA SAMBUNGAN PIPA HIGH PRESSURE AKIBAT PENAMBAHAN STIFFENER MENGGUNAKAN ANSYS

Delima Yanti Sari, Wanda Afnison, Waskito, Ridho Ogarbel Putera
article en

Abstract

High-pressure piping flange connections are susceptible to stress concentration due to geometric discontinuities, which may affect structural integrity. This study aims to analyze stress distribution and evaluate the effects of variations in the number and thickness of stiffener plates on Von Mises stress, stress concentration factor (SCF), and deformation in an ASME B16.5 Class 900 NPS 6 weld neck flange made of ASTM A105 steel. The study employed the finite element method using the Static Structural module in ANSYS Workbench, with an internal pressure of 15.3 MPa and a bolt pretension of 50% of the bolt yield strength. Six configurations were analyzed, consisting of one unreinforced model and five stiffener variations. The simulation results showed reductions in maximum stress of 9.31–15.87% and deformation of 22.24–25.60% compared with the unreinforced configuration. The configuration with eight 12-mm-thick stiffeners produced the lowest maximum stress of 202.47 MPa, whereas the configuration with twelve 4-mm-thick stiffeners achieved the highest reinforcement efficiency index. However, the mesh convergence study indicated that numerical stability had not been consistently achieved. Therefore, comparisons among configurations remain preliminary and require further numerical investigation. ABSTRAK Sambungan flange pada sistem perpipaan bertekanan tinggi rentan mengalami konsentrasi tegangan akibat diskontinuitas geometri yang dapat memengaruhi integritas struktural. Penelitian ini bertujuan menganalisis distribusi tegangan serta mengevaluasi pengaruh variasi jumlah dan ketebalan stiffener plate terhadap tegangan Von Mises, faktor konsentrasi tegangan (SCF), dan deformasi pada weld neck flange ASME B16.5 Class 900 NPS 6 berbahan ASTM A105. Penelitian menggunakan metode elemen hingga melalui ANSYS Workbench modul Static Structural dengan tekanan internal 15,3 MPa dan prategangan baut sebesar 50% tegangan luluh baut. Enam konfigurasi dianalisis, meliputi satu model tanpa penguatan dan lima variasi stiffener. Hasil simulasi menunjukkan penurunan tegangan maksimum sebesar 9,31–15,87% dan deformasi sebesar 22,24–25,60% dibandingkan konfigurasi tanpa penguatan. Konfigurasi delapan stiffener setebal 12 mm menghasilkan tegangan maksimum terendah sebesar 202,47 MPa, sedangkan konfigurasi dua belas stiffener setebal 4 mm menghasilkan indeks efisiensi penguatan tertinggi. Namun, hasil studi konvergensi mesh menunjukkan bahwa kestabilan numerik belum terpenuhi secara konsisten. Oleh karena itu, hasil perbandingan konfigurasi masih bersifat sementara dan memerlukan pengujian numerik lanjutan.

KNOWLEDGE Jurnal Inovasi Hasil Penelitian dan PengembanganVol. 6(4)
State University of Padang (ID)
Engineering Structural Analysis Methods
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon