FRICTIONAL CHARACTERISTICS OF A TRIBOSYSTEM WITH A COMBINED CONTACT SURFACE IN DRY AND BOUNDARY FRICTION MODES

The study objective is to determine the features of the contact interaction between the elements of a tribological pair with a combined contact surface under dry and boundary friction conditions. The task the paper is devoted to is assessing the influence of sliding velocity and lubricant on the friction characteristics of a friction system with a combined surface “structural steel – deposited metal”, simulating the contact between the working edge of a tool and a combined machinable material. Research methods. The friction characteristics are assessed using the “indenter on disc” friction scheme, with the sliding velocity varied both in a dry state and with the use of commercial lubricating and cooling fluids. The indenter materials are hard alloy T15K6 and high speed steel R18; the combined disc surface consists of structural steel 09G2S and metal deposited with an electrode. During the experiments, the values of the friction coefficients were recorded. Novelty of the work. The influence of sliding velocity and lubricant on changes in the friction factor when passing through material separation boundaries for a tribosystem with a combined contact surface is revealed. Research results. The friction factor values increase when the tribocontact moves from the area of structural steel into the zone of harder deposited metal, and their growth in dry friction mode can be up to 2.5 times higher the initial value. The transition of the tribosystem to the boundary lubrication mode when using aqueous emulsions of lubricating and cooling fluids makes it possible to reduce the increase in the friction factor at the interface between the materials to 1.05–1.25 times from the original value. It is found out that the increase value of the friction factor in the transition area varies non linearly with the sliding velocity and passes through a minimum within a certain range. At the same time, the use of a lubricant makes it possible to stabilize the system state at a higher level of sliding velocities than for a similar tribological pair in the dry friction mode. Conclusions: The patterns found in the study can be used when selecting cutting conditions for turning workpieces consisting of several different materials. A promising direction in this case will be to determine cutting speeds using a calculation method, which, while meeting other technological requirements, will ensure minimal changes in the frictional characteristics of the contact zone on the working edges of the tool.

Authors

Institutions

Publication Details

Journal
Transport engineering
Published
2026-11-14
DOI
https://doi.org/10.30987/2782-5957-2026-11-26-32
Primary Topic
Advanced machining processes and optimization
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

FRICTIONAL CHARACTERISTICS OF A TRIBOSYSTEM WITH A COMBINED CONTACT SURFACE IN DRY AND BOUNDARY FRICTION MODES

Фоминов Евгений Валерьевич
Transport engineering
Advanced machining processes and optimization
article

FRICTIONAL CHARACTERISTICS OF A TRIBOSYSTEM WITH A COMBINED CONTACT SURFACE IN DRY AND BOUNDARY FRICTION MODES

Фоминов Евгений Валерьевич
article en

Abstract

The study objective is to determine the features of the contact interaction between the elements of a tribological pair with a combined contact surface under dry and boundary friction conditions. The task the paper is devoted to is assessing the influence of sliding velocity and lubricant on the friction characteristics of a friction system with a combined surface “structural steel – deposited metal”, simulating the contact between the working edge of a tool and a combined machinable material. Research methods. The friction characteristics are assessed using the “indenter on disc” friction scheme, with the sliding velocity varied both in a dry state and with the use of commercial lubricating and cooling fluids. The indenter materials are hard alloy T15K6 and high speed steel R18; the combined disc surface consists of structural steel 09G2S and metal deposited with an electrode. During the experiments, the values of the friction coefficients were recorded. Novelty of the work. The influence of sliding velocity and lubricant on changes in the friction factor when passing through material separation boundaries for a tribosystem with a combined contact surface is revealed. Research results. The friction factor values increase when the tribocontact moves from the area of structural steel into the zone of harder deposited metal, and their growth in dry friction mode can be up to 2.5 times higher the initial value. The transition of the tribosystem to the boundary lubrication mode when using aqueous emulsions of lubricating and cooling fluids makes it possible to reduce the increase in the friction factor at the interface between the materials to 1.05–1.25 times from the original value. It is found out that the increase value of the friction factor in the transition area varies non linearly with the sliding velocity and passes through a minimum within a certain range. At the same time, the use of a lubricant makes it possible to stabilize the system state at a higher level of sliding velocities than for a similar tribological pair in the dry friction mode. Conclusions: The patterns found in the study can be used when selecting cutting conditions for turning workpieces consisting of several different materials. A promising direction in this case will be to determine cutting speeds using a calculation method, which, while meeting other technological requirements, will ensure minimal changes in the frictional characteristics of the contact zone on the working edges of the tool.

Transport engineeringVol. 2026(11)
Don State Technical University (RU)
Advanced machining processes and optimization
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon