Development and Preliminary Evaluation of a Poka-Yoke Support Hook for Brake Calipers During Brake Pad Replacement

Temporarily supporting a removed brake caliper is a necessary part of brake maintenance because the hydraulic hose must not serve as a suspension element. This study examines the design of a caliper support hook made from AISI 1020 steel and interprets the graphical evidence from a static simulation. An applied case study was conducted, integrating a documentary review, an exploratory literature search guided by PRISMA transparency criteria, failure mode and effects analysis (FMEA), and interpretation of four numerical plots and one material data sheet. The model shown contains two hooks, perforated arms, joints, and a diagonal bar. The plot scales show upper limits of 36.56 MPa for von Mises equivalent stress, 0.1925 mm for resultant displacement, and 1.339 × 10⁻⁴ for equivalent strain. The visible distribution concentrates higher stress and strain near the upper-hook transition, while displacement increases toward the loaded lower end. The AISI 1020 data sheet indicates a yield strength of 351.571 MPa, consistent with the displayed minimum factor of safety of approximately 9.6. However, load, contact, and mesh-convergence documentation is missing, so no allowable capacity is established. FMEA ranks unintended disengagement as the highest internal priority, a condition that the structural plot does not verify. The 10.0- and 8.8-minute values represent a projected 12% reduction, not workshop measurements. Improvements to the geometric transition, retention, and joint modeling are proposed, together with a verification plan. No physical prototype exists; drawings remain pending, and an illustrative render is included. The contribution is to connect the available numerical results with design decisions and explicit limits on interpretation.

Authors

Institutions

Publication Details

Journal
International Journal of Research and Innovation in Social Science
Published
2026-11-14
DOI
https://doi.org/10.47772/ijriss.2026.102500014
Primary Topic
Engineering Applied Research
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Development and Preliminary Evaluation of a Poka-Yoke Support Hook for Brake Calipers During Brake Pad Replacement

Héctor Luis Gutiérrez Martínez, María Fernanda Ramos González, Emilio Merlo Peña, Jaime Brayan Cruz Ortiz et al.
International Journal of Research and Innovation in Social Science
Engineering Applied Research
article

Development and Preliminary Evaluation of a Poka-Yoke Support Hook for Brake Calipers During Brake Pad Replacement

Héctor Luis Gutiérrez Martínez, María Fernanda Ramos González, Emilio Merlo Peña, Jaime Brayan Cruz Ortiz, Jesús Sebastián Badillo Lara, Emanuel Lango Fragoso
article en

Abstract

Temporarily supporting a removed brake caliper is a necessary part of brake maintenance because the hydraulic hose must not serve as a suspension element. This study examines the design of a caliper support hook made from AISI 1020 steel and interprets the graphical evidence from a static simulation. An applied case study was conducted, integrating a documentary review, an exploratory literature search guided by PRISMA transparency criteria, failure mode and effects analysis (FMEA), and interpretation of four numerical plots and one material data sheet. The model shown contains two hooks, perforated arms, joints, and a diagonal bar. The plot scales show upper limits of 36.56 MPa for von Mises equivalent stress, 0.1925 mm for resultant displacement, and 1.339 × 10⁻⁴ for equivalent strain. The visible distribution concentrates higher stress and strain near the upper-hook transition, while displacement increases toward the loaded lower end. The AISI 1020 data sheet indicates a yield strength of 351.571 MPa, consistent with the displayed minimum factor of safety of approximately 9.6. However, load, contact, and mesh-convergence documentation is missing, so no allowable capacity is established. FMEA ranks unintended disengagement as the highest internal priority, a condition that the structural plot does not verify. The 10.0- and 8.8-minute values represent a projected 12% reduction, not workshop measurements. Improvements to the geometric transition, retention, and joint modeling are proposed, together with a verification plan. No physical prototype exists; drawings remain pending, and an illustrative render is included. The contribution is to connect the available numerical results with design decisions and explicit limits on interpretation.

International Journal of Research and Innovation in Social ScienceVol. 10(25)
Mexican Association for the Clinical Research (MX), Instituto Tecnológico de Toluca (MX)
Engineering Applied Research
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon