Development of a High‐Strength Two‐Component Polyurethane Structural Adhesive for Extreme Cryogenic Environments

ABSTRACT Structural adhesives used in liquefied natural gas (LNG) containment systems must retain reliable load transfer under severe thermomechanical mismatch near the boiling point of methane (approximately −163°C). Here, a series of two‐component polyurethane (PU) structural adhesives was developed using a phenyl‐based diol/diamine chain‐extender combination, an MDI/PM‐200‐based isocyanate‐terminated prepolymer, and silica microparticles. The best‐performing formulation within the investigated composition range, PU‐C5‐50, achieved lap‐shear strengths of 11.6 MPa at room temperature and 13.02 MPa at −163°C on sandblasted steel, corresponding to increases of 41.3% and 44.0%, respectively, relative to the unfilled PU‐C5‐0 formulation. Composition–property analysis showed that increasing PM‐200 incorporation was accompanied by an increased fraction of hydrogen‐bonded carbonyl species and enhanced hard‐segment association, while silica addition increased joint strength and promoted a transition from predominantly interfacial to cohesive failure. Contact‐angle measurements indicated favorable wetting of PU‐C5‐50 on sandblasted steel. Together with the observed failure‐mode evolution, the interfacial bonding is proposed to involve intimate adhesive–substrate contact, mechanical interlocking on the sandblasted surface, polar intermolecular interactions, and effective cohesive stress transfer. DMA, DSC, SEM, and SAXS indicated a highly crosslinked, predominantly amorphous and structurally isotropic material with disordered local hard‐segment aggregation rather than long‐range ordered microphase separation. These results demonstrate a practical route to combining high cohesive strength, interfacial compatibility, and short‐term cryogenic lap‐shear performance in two‐component PU adhesives for LNG‐related structural bonding.

Authors

Institutions

Publication Details

Journal
Polymer Engineering and Science
Published
2026-11-14
DOI
https://doi.org/10.1002/pen.71001
Primary Topic
Material Properties and Applications
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Development of a High‐Strength Two‐Component Polyurethane Structural Adhesive for Extreme Cryogenic Environments

魏柳荷, Congshu Huang, Yanhui Cao, 岳中凯 et al.
Polymer Engineering and Science
Material Properties and Applications
article

Development of a High‐Strength Two‐Component Polyurethane Structural Adhesive for Extreme Cryogenic Environments

魏柳荷, Congshu Huang, Yanhui Cao, 岳中凯, Peixin Niu, Yuhan Li, Jin Wang, Yu Liang, Kaifeng Chen, Bingyang Wang
article en

Abstract

ABSTRACT Structural adhesives used in liquefied natural gas (LNG) containment systems must retain reliable load transfer under severe thermomechanical mismatch near the boiling point of methane (approximately −163°C). Here, a series of two‐component polyurethane (PU) structural adhesives was developed using a phenyl‐based diol/diamine chain‐extender combination, an MDI/PM‐200‐based isocyanate‐terminated prepolymer, and silica microparticles. The best‐performing formulation within the investigated composition range, PU‐C5‐50, achieved lap‐shear strengths of 11.6 MPa at room temperature and 13.02 MPa at −163°C on sandblasted steel, corresponding to increases of 41.3% and 44.0%, respectively, relative to the unfilled PU‐C5‐0 formulation. Composition–property analysis showed that increasing PM‐200 incorporation was accompanied by an increased fraction of hydrogen‐bonded carbonyl species and enhanced hard‐segment association, while silica addition increased joint strength and promoted a transition from predominantly interfacial to cohesive failure. Contact‐angle measurements indicated favorable wetting of PU‐C5‐50 on sandblasted steel. Together with the observed failure‐mode evolution, the interfacial bonding is proposed to involve intimate adhesive–substrate contact, mechanical interlocking on the sandblasted surface, polar intermolecular interactions, and effective cohesive stress transfer. DMA, DSC, SEM, and SAXS indicated a highly crosslinked, predominantly amorphous and structurally isotropic material with disordered local hard‐segment aggregation rather than long‐range ordered microphase separation. These results demonstrate a practical route to combining high cohesive strength, interfacial compatibility, and short‐term cryogenic lap‐shear performance in two‐component PU adhesives for LNG‐related structural bonding.

Polymer Engineering and Science
Xiamen University (CN), Zhengzhou University (CN), Henan University of Engineering (CN), Luoyang Ship Material Research Institute (CN)
Material Properties and Applications
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon