Increasing Productivity in Hidalgo through Additive Manufacturing: A Case Study in SMEs

Micro, small, and medium-sized enterprises (SMEs) form the backbone of regional economies such as Hidalgo, Mexico, yet they frequently exhibit productivity lags relative to larger firms due to limited technology adoption, inefficient traditional processes, and high material waste. Additive manufacturing (AM), particularly low-cost fused deposition modeling (FDM), offers a promising pathway to address these constraints by enabling on-demand production, reduced waste, and shorter cycle times without large capital investments. This study evaluates the impact of implementing accessible AM technologies on productivity metrics in a representative manufacturing SME in Hidalgo and proposes a replicable six-phase implementation methodology. A mixed-methods experimental case study was employed. A PRISMA systematic review of 20 articles (2016–2026) informed the intervention design and variable selection. The empirical component consisted of a longitudinal single-case study with four phases: baseline diagnosis, process redesign, a six-month pilot, and evaluation. Quantitative pre-post comparisons of cycle time, waste rate, monthly production, operational efficiency, and overall productivity were triangulated with qualitative data from surveys and interviews. The pilot, based on open-source FDM printers and software, produced substantial improvements. Cycle time decreased from 45 to 27 minutes per unit (40% reduction), material waste declined by approximately 40%, monthly production rose from 150 to 200 units (33% increase), operational efficiency improved from 60% to 90%, and overall productivity increased by 35%. These gains were achieved with moderate investment and targeted training of 15–25% of production staff. The findings support the hypothesis and align with literature benchmarks for low-volume AM applications while addressing the scarcity of experimental pre-post evidence in regional Mexican SMEs. The proposed six-phase methodology provides a practical, low-risk pathway for other resource-constrained SMEs. Limitations of the single-case design are acknowledged, and future research directions include multi-firm implementations and longer-term sustainability assessment

Authors

Institutions

Publication Details

Journal
International Journal of Research and Innovation in Social Science
Published
2026-11-14
DOI
https://doi.org/10.47772/ijriss.2026.102500004
Primary Topic
Additive Manufacturing and 3D Printing Technologies
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Increasing Productivity in Hidalgo through Additive Manufacturing: A Case Study in SMEs

Enrique de Jesús Mohedano Torres, Adrián Sánchez Ortega, Guillermo Acosta Mendoza, Alejandra Lugo Islas et al.
International Journal of Research and Innovation in Social Science
Additive Manufacturing and 3D Printing Technologies
article

Increasing Productivity in Hidalgo through Additive Manufacturing: A Case Study in SMEs

Enrique de Jesús Mohedano Torres, Adrián Sánchez Ortega, Guillermo Acosta Mendoza, Alejandra Lugo Islas, Keyla Espinosa Ramos, Gabriela Calva Arcega
article en

Abstract

Micro, small, and medium-sized enterprises (SMEs) form the backbone of regional economies such as Hidalgo, Mexico, yet they frequently exhibit productivity lags relative to larger firms due to limited technology adoption, inefficient traditional processes, and high material waste. Additive manufacturing (AM), particularly low-cost fused deposition modeling (FDM), offers a promising pathway to address these constraints by enabling on-demand production, reduced waste, and shorter cycle times without large capital investments. This study evaluates the impact of implementing accessible AM technologies on productivity metrics in a representative manufacturing SME in Hidalgo and proposes a replicable six-phase implementation methodology. A mixed-methods experimental case study was employed. A PRISMA systematic review of 20 articles (2016–2026) informed the intervention design and variable selection. The empirical component consisted of a longitudinal single-case study with four phases: baseline diagnosis, process redesign, a six-month pilot, and evaluation. Quantitative pre-post comparisons of cycle time, waste rate, monthly production, operational efficiency, and overall productivity were triangulated with qualitative data from surveys and interviews. The pilot, based on open-source FDM printers and software, produced substantial improvements. Cycle time decreased from 45 to 27 minutes per unit (40% reduction), material waste declined by approximately 40%, monthly production rose from 150 to 200 units (33% increase), operational efficiency improved from 60% to 90%, and overall productivity increased by 35%. These gains were achieved with moderate investment and targeted training of 15–25% of production staff. The findings support the hypothesis and align with literature benchmarks for low-volume AM applications while addressing the scarcity of experimental pre-post evidence in regional Mexican SMEs. The proposed six-phase methodology provides a practical, low-risk pathway for other resource-constrained SMEs. Limitations of the single-case design are acknowledged, and future research directions include multi-firm implementations and longer-term sustainability assessment

International Journal of Research and Innovation in Social ScienceVol. 10(25)
Tecnológico Nacional de México, Campus Pachuca (MX)
Additive Manufacturing and 3D Printing Technologies
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon