Experimental investigation of electrochemical machining performance of AISI 304 stainless steel using a palladium-coated electrode with ascorbic acid - mixed electrolyte: Original scientific paper

Passive film generation, buildup of insoluble hydroxide sludge, and dimensional errors caused by uncontrolled anodic dissolution are issues that arise during electrochemical machining (ECM) of AISI 304 stainless steel (SS). While electrode coatings and electrolyte additives have been studied separately, the combination of palladium (Pd)-coated electrodes and ascorbic acid-modified electrolytes to enhance ECM performance has received less attention. Using a Pd-coated needle electrode and a sodium nitrate (NaNO3) electrolyte containing 10 g L-1 ascorbic acid, this study experimentally analyses the machining properties of AISI 304 SS. The effects on machining rate (MR) and overcut (OC) of electrolyte concentration (0.328 to 0.386 mol L-2), machining voltage (7 to 12 V), duty cycle (40 to 90 %), and pulse frequency (40 to 90 Hz) were methodically assessed. The machined-hole shape was examined using scanning electron microscopy (SEM), and the electrode substrate was characterized using energy-dispersive X-ray spectroscopy. Experimental data show that increasing electrolyte concentration, machining voltage, duty cycle, and pulse frequency enhanced MR and decreased OC within the examined ranges. With a 58.4 % improvement in MR from 0.219 to 0.347 μm s-1 and a 23.4 % decrease in OC from 290 to 222 μm when frequency increased from 40 to 90 Hz, pulse frequency showed the greatest increase in MR. At an electrolyte concentration of 0.386 mol L-1, a machining voltage of 12 V, a 90 % duty cycle, and a pulse frequency of 90 Hz, the maximum recorded MR of 0.347 μm s-1 with an OC of 222 μm was attained. Nearly circular machined holes with comparatively clean edges and few surface deposits were visible in SEM examinations, suggesting regulated anodic dissolution. By reducing Fe3+ to Fe2+, ascorbic acid is suggested to prevent the formation of insoluble ferric hydroxide, promoting electrolyte stability and eliminating reaction products. Using a Pd-coated electrode and an electrolyte modified with ascorbic acid, the study determines an experimentally assessed processing window for ECM of AISI 304 stainless steel, offering insights into increasing machining productivity and dimensional correctness.

Authors

Publication Details

Journal
Journal of Electrochemical Science and Engineering
Published
2026-11-14
DOI
https://doi.org/10.5599/jese.3660
Primary Topic
Advanced Machining and Optimization Techniques
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Experimental investigation of electrochemical machining performance of AISI 304 stainless steel using a palladium-coated electrode with ascorbic acid - mixed electrolyte: Original scientific paper

R. Thirunavukkarasu, J.R. Vinod Kumaar, L. Sankaralingam, K. G. Saravanan et al.
Journal of Electrochemical Science and Engineering
Advanced Machining and Optimization Techniques
article

Experimental investigation of electrochemical machining performance of AISI 304 stainless steel using a palladium-coated electrode with ascorbic acid - mixed electrolyte: Original scientific paper

R. Thirunavukkarasu, J.R. Vinod Kumaar, L. Sankaralingam, K. G. Saravanan, Sanjeev Kumar, S. Karthikeyan, Thirugnanasambandham Thangavel, Nethaji Subash Chandra Bose Ayyavoo
article en

Abstract

Passive film generation, buildup of insoluble hydroxide sludge, and dimensional errors caused by uncontrolled anodic dissolution are issues that arise during electrochemical machining (ECM) of AISI 304 stainless steel (SS). While electrode coatings and electrolyte additives have been studied separately, the combination of palladium (Pd)-coated electrodes and ascorbic acid-modified electrolytes to enhance ECM performance has received less attention. Using a Pd-coated needle electrode and a sodium nitrate (NaNO3) electrolyte containing 10 g L-1 ascorbic acid, this study experimentally analyses the machining properties of AISI 304 SS. The effects on machining rate (MR) and overcut (OC) of electrolyte concentration (0.328 to 0.386 mol L-2), machining voltage (7 to 12 V), duty cycle (40 to 90 %), and pulse frequency (40 to 90 Hz) were methodically assessed. The machined-hole shape was examined using scanning electron microscopy (SEM), and the electrode substrate was characterized using energy-dispersive X-ray spectroscopy. Experimental data show that increasing electrolyte concentration, machining voltage, duty cycle, and pulse frequency enhanced MR and decreased OC within the examined ranges. With a 58.4 % improvement in MR from 0.219 to 0.347 μm s-1 and a 23.4 % decrease in OC from 290 to 222 μm when frequency increased from 40 to 90 Hz, pulse frequency showed the greatest increase in MR. At an electrolyte concentration of 0.386 mol L-1, a machining voltage of 12 V, a 90 % duty cycle, and a pulse frequency of 90 Hz, the maximum recorded MR of 0.347 μm s-1 with an OC of 222 μm was attained. Nearly circular machined holes with comparatively clean edges and few surface deposits were visible in SEM examinations, suggesting regulated anodic dissolution. By reducing Fe3+ to Fe2+, ascorbic acid is suggested to prevent the formation of insoluble ferric hydroxide, promoting electrolyte stability and eliminating reaction products. Using a Pd-coated electrode and an electrolyte modified with ascorbic acid, the study determines an experimentally assessed processing window for ECM of AISI 304 stainless steel, offering insights into increasing machining productivity and dimensional correctness.

Journal of Electrochemical Science and EngineeringVol. 16
Advanced Machining and Optimization Techniques
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon