Effect of Pulse-Duration Ratio on Microstructural Evolution, Mechanical Properties, Phase Transformation, and Corrosion Resistance of Autogenously DPTIG-Welded Nitinol Sheets

Abstract Joining thin Nitinol sheets remains challenging because the thermal cycles associated with fusion welding can substantially alter their microstructure, mechanical properties, phase transformation behaviour, and corrosion resistance. In this study, 1 mm-thick Nitinol sheets were autogenously welded using double-pulse tungsten inert gas (DPTIG) welding to investigate the effects of pulse-duration ratio on weld bead geometry, microstructure, mechanical properties, phase transformation behaviour, and corrosion performance. Three pulse-duration ratios (50–50%, 40–60%, and 60 − 40%) were investigated. Full penetration was achieved under all welding conditions, while the 40–60% condition produced the narrowest weld bead and promoted grain refinement. The fusion zone predominantly comprised B2 austenite with columnar grains, alongside the formation of Ti₂Ni and Ni₃Ti intermetallic phases. Among the investigated conditions, the 40–60% ratio yielded the finest average grain size (24 ± 2 µm), the highest high-angle grain boundary (HAGB) fraction (76%), and the highest tensile strength (583 ± 11 MPa), representing an approximately 3% improvement over the 50–50% condition. Differential scanning calorimetry (DSC) revealed the B2-B19′ martensitic transformation, with no discernible R-phase transformation peak. In contrast, the 60 − 40% condition exhibited the lowest corrosion rate of 0.00402 mm/year. These findings demonstrate that pulse-duration ratio influences weld geometry, microstructural evolution, tensile performance, phase transformation behavior, and corrosion resistance in DPTIG-welded Nitinol sheets, highlighting its potential as a process parameter for tailoring the properties of welded Nitinol components.

Authors

Institutions

Publication Details

Journal
Research Square
Published
2026-11-13
DOI
https://doi.org/10.21203/rs.3.rs-11376218/v1
Primary Topic
Welding Techniques and Residual Stresses
Type
preprint
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
preprint

Effect of Pulse-Duration Ratio on Microstructural Evolution, Mechanical Properties, Phase Transformation, and Corrosion Resistance of Autogenously DPTIG-Welded Nitinol Sheets

Chandan Pandey, Manoj Samson R, Sanjeev Kumar, Saravanakumar R
Research Square
Welding Techniques and Residual Stresses
preprint

Effect of Pulse-Duration Ratio on Microstructural Evolution, Mechanical Properties, Phase Transformation, and Corrosion Resistance of Autogenously DPTIG-Welded Nitinol Sheets

Chandan Pandey, Manoj Samson R, Sanjeev Kumar, Saravanakumar R
preprint en

Abstract

Abstract Joining thin Nitinol sheets remains challenging because the thermal cycles associated with fusion welding can substantially alter their microstructure, mechanical properties, phase transformation behaviour, and corrosion resistance. In this study, 1 mm-thick Nitinol sheets were autogenously welded using double-pulse tungsten inert gas (DPTIG) welding to investigate the effects of pulse-duration ratio on weld bead geometry, microstructure, mechanical properties, phase transformation behaviour, and corrosion performance. Three pulse-duration ratios (50–50%, 40–60%, and 60 − 40%) were investigated. Full penetration was achieved under all welding conditions, while the 40–60% condition produced the narrowest weld bead and promoted grain refinement. The fusion zone predominantly comprised B2 austenite with columnar grains, alongside the formation of Ti₂Ni and Ni₃Ti intermetallic phases. Among the investigated conditions, the 40–60% ratio yielded the finest average grain size (24 ± 2 µm), the highest high-angle grain boundary (HAGB) fraction (76%), and the highest tensile strength (583 ± 11 MPa), representing an approximately 3% improvement over the 50–50% condition. Differential scanning calorimetry (DSC) revealed the B2-B19′ martensitic transformation, with no discernible R-phase transformation peak. In contrast, the 60 − 40% condition exhibited the lowest corrosion rate of 0.00402 mm/year. These findings demonstrate that pulse-duration ratio influences weld geometry, microstructural evolution, tensile performance, phase transformation behavior, and corrosion resistance in DPTIG-welded Nitinol sheets, highlighting its potential as a process parameter for tailoring the properties of welded Nitinol components.

Research Square
SRM Institute of Science and Technology (IN), Indian Institute of Technology Jodhpur (IN)
Welding Techniques and Residual Stresses
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon