Collision Response Analysis of a Suspended Rubber-Tube Height-Restriction Warning Frame Subjected to Overheight Vehicle Impact Using LS-DYNA

Traditional height-limiting warning barriers address the issues of susceptibility to damage and difficulty in operation and maintenance. This paper proposes a rubber-tube-suspended height-restriction frame. Based on the LSDYNA explicit dynamics platform, a finite element model for an over-height vehicle height-restriction frame was developed to simulate collisions between over-height vehicles and the rubber-tube height-restriction frame. The model systematically analyzes the collision response patterns under full-width frontal collisions and lateral collisions with offsets of 1/2 and 1/4. The results indicate that a frontal collision consists of two concentrated contact phases: an initial high-intensity impact followed by a secondary low-intensity impact. During these phases, the maximum contact reaction force reaches 148.3 kN, providing effective tactile feedback for the driver without damaging the vehicle’s roof steel structure. The secondary impact occurs during the phase where the vehicle and the rubber tube move in the same direction, at which point the peak contact force drops to 35 kN. This energy dissipation is attributed to the combined effect of reduced relative velocity at the contact interface and the unloading of tangential slip. Energy analysis shows that impact kinetic energy is dissipated gradually through a hierarchical process: it is first converted into strain energy, and subsequently into frictional energy, rotational kinetic energy, and gravitational potential energy. Among these dissipation pathways, frictional energy at the vehicle-tube interface (approximately 3.0 × 106 N × mm) dominates in the early stage, whereas frictional energy at the tube–beam interface (approximately 3.8 × 106 N × mm) becomes the primary dissipation mechanism during the long-period oscillation stage. The maximum von Mises equivalent stress in the rubber component is 1.678 MPa, providing sufficient safety margin. Offset collisions can reduce peak contact forces by 32.6–46.5%, although local stresses increase slightly. However, under all test conditions, the maximum von Mises stress in the rubber component remains below the material’s tensile strength, thereby ensuring a sufficient safety margin. This suspended rubber-tube-type high-speed limit warning barrier provides effective contact warning under a variety of impact conditions while minimizing damage to both the vehicle and the barrier itself. The research findings provide a quantitative basis for the design of passive high-speed limit warning facilities.

Authors

Institutions

Publication Details

Journal
Materials
Published
2026-11-13
DOI
https://doi.org/10.3390/ma19224829
Primary Topic
Transportation Safety and Impact Analysis
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Collision Response Analysis of a Suspended Rubber-Tube Height-Restriction Warning Frame Subjected to Overheight Vehicle Impact Using LS-DYNA

Lintao Cao, Jiawei Yan
Materials
Transportation Safety and Impact Analysis
article

Collision Response Analysis of a Suspended Rubber-Tube Height-Restriction Warning Frame Subjected to Overheight Vehicle Impact Using LS-DYNA

Lintao Cao, Jiawei Yan
article en

Abstract

Traditional height-limiting warning barriers address the issues of susceptibility to damage and difficulty in operation and maintenance. This paper proposes a rubber-tube-suspended height-restriction frame. Based on the LSDYNA explicit dynamics platform, a finite element model for an over-height vehicle height-restriction frame was developed to simulate collisions between over-height vehicles and the rubber-tube height-restriction frame. The model systematically analyzes the collision response patterns under full-width frontal collisions and lateral collisions with offsets of 1/2 and 1/4. The results indicate that a frontal collision consists of two concentrated contact phases: an initial high-intensity impact followed by a secondary low-intensity impact. During these phases, the maximum contact reaction force reaches 148.3 kN, providing effective tactile feedback for the driver without damaging the vehicle’s roof steel structure. The secondary impact occurs during the phase where the vehicle and the rubber tube move in the same direction, at which point the peak contact force drops to 35 kN. This energy dissipation is attributed to the combined effect of reduced relative velocity at the contact interface and the unloading of tangential slip. Energy analysis shows that impact kinetic energy is dissipated gradually through a hierarchical process: it is first converted into strain energy, and subsequently into frictional energy, rotational kinetic energy, and gravitational potential energy. Among these dissipation pathways, frictional energy at the vehicle-tube interface (approximately 3.0 × 106 N × mm) dominates in the early stage, whereas frictional energy at the tube–beam interface (approximately 3.8 × 106 N × mm) becomes the primary dissipation mechanism during the long-period oscillation stage. The maximum von Mises equivalent stress in the rubber component is 1.678 MPa, providing sufficient safety margin. Offset collisions can reduce peak contact forces by 32.6–46.5%, although local stresses increase slightly. However, under all test conditions, the maximum von Mises stress in the rubber component remains below the material’s tensile strength, thereby ensuring a sufficient safety margin. This suspended rubber-tube-type high-speed limit warning barrier provides effective contact warning under a variety of impact conditions while minimizing damage to both the vehicle and the barrier itself. The research findings provide a quantitative basis for the design of passive high-speed limit warning facilities.

MaterialsVol. 19(22)
Hubei University of Arts and Science (CN)
Transportation Safety and Impact Analysis
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon