Weldability of Low-Manganese Filler Metals: Mechanical Properties and Solidification Cracking in MAG Welding

Abstract The reduction of the occupational exposure limit for manganese to 0.05 mg/m³ in 2019 has led to the development of low-manganese filler metals designed to reduce fume emissions during welding. These consumables typically compensate for the lower manganese content through increased carbon levels and the addition of alloying elements, which may modify the microstructure and mechanical behaviour of the weld metal. In addition, reducing manganese content could affect resistance to solidification cracking. This study investigates the weldability of low-manganese flux-cored and metal-cored filler metals compared with conventional consumables. Mechanical properties and hot-cracking susceptibility are evaluated as a function of welding parameters. Welded joints were produced using two configurations. First, butt welds were manufactured at two heat inputs (1 and 2 kJ/mm) to assess tensile properties, hardness and Charpy V impact toughness in a low-dilution fusion zone. Second, a round-bar-through-plate test was used to determine the critical welding speed associated with solidification cracking at a heat input of 1 kJ/mm. The results show that reducing manganese content has a limited effect on tensile properties, although a slight decrease in strength is observed. Impact toughness is comparable for metal-cored wires but reduced for low-manganese flux-cored wires. Increasing heat input decreases strength but can improve toughness for low-manganese metal-cored consumables. Regarding solidification cracking, no significant influence of manganese content is observed for C35 steel, whereas for S355 steel, the use of low-manganese wires leads to a reduction in critical welding speed. Overall, low-manganese filler metals provide weldability comparable to that of conventional consumables under most conditions but may limit performance in applications requiring high toughness or high welding speeds.

Authors

Institutions

Publication Details

Journal
Research Square
Published
2026-11-13
DOI
https://doi.org/10.21203/rs.3.rs-11202427/v1
Primary Topic
Welding Techniques and Residual Stresses
Type
preprint
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
preprint

Weldability of Low-Manganese Filler Metals: Mechanical Properties and Solidification Cracking in MAG Welding

Laurent Jubin, Lauriane Guilmois, Simon Pigaux-Leys
Research Square
Welding Techniques and Residual Stresses
preprint

Weldability of Low-Manganese Filler Metals: Mechanical Properties and Solidification Cracking in MAG Welding

Laurent Jubin, Lauriane Guilmois, Simon Pigaux-Leys
preprint en

Abstract

Abstract The reduction of the occupational exposure limit for manganese to 0.05 mg/m³ in 2019 has led to the development of low-manganese filler metals designed to reduce fume emissions during welding. These consumables typically compensate for the lower manganese content through increased carbon levels and the addition of alloying elements, which may modify the microstructure and mechanical behaviour of the weld metal. In addition, reducing manganese content could affect resistance to solidification cracking. This study investigates the weldability of low-manganese flux-cored and metal-cored filler metals compared with conventional consumables. Mechanical properties and hot-cracking susceptibility are evaluated as a function of welding parameters. Welded joints were produced using two configurations. First, butt welds were manufactured at two heat inputs (1 and 2 kJ/mm) to assess tensile properties, hardness and Charpy V impact toughness in a low-dilution fusion zone. Second, a round-bar-through-plate test was used to determine the critical welding speed associated with solidification cracking at a heat input of 1 kJ/mm. The results show that reducing manganese content has a limited effect on tensile properties, although a slight decrease in strength is observed. Impact toughness is comparable for metal-cored wires but reduced for low-manganese flux-cored wires. Increasing heat input decreases strength but can improve toughness for low-manganese metal-cored consumables. Regarding solidification cracking, no significant influence of manganese content is observed for C35 steel, whereas for S355 steel, the use of low-manganese wires leads to a reduction in critical welding speed. Overall, low-manganese filler metals provide weldability comparable to that of conventional consumables under most conditions but may limit performance in applications requiring high toughness or high welding speeds.

Research Square
Centre Technique des Industries Mécaniques (FR)
Welding Techniques and Residual Stresses
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon