Integrated mechanical earth modeling and finite-element assessment of casing-collapse mitigation strategies in high-stress salt-bearing caprocks

Casing collapse in wells penetrating salt-bearing caprocks is a significant well-integrity concern because anisotropic in-situ stresses and mechanical contrasts between geological formations can produce non-uniform loading. This study integrates a Mechanical Earth Model (MEM) with finite-element analysis (FEA) to evaluate the mechanical response of alternative casing configurations in a deep well. Acoustic and density logs from 3050 to 3618 m were used to estimate formation elastic properties and in-situ stresses. These estimates were applied to models of the formation–cement–casing system. The baseline 9.625-in production casing was compared with four alternatives: a thicker-wall T-95 casing configuration, a thick-wall L-80 casing, a 7-in inner liner installed within the existing casing, and a standalone 7-in casing. The predicted maximum von Mises stress and radial displacement were used as the primary response indicators. The baseline configuration produced a maximum von Mises stress of 1010.2 MPa and a displacement of 4.574 cm in Gachsaran Section 2. The corresponding values were 871.4 MPa and 3.821 cm for the T-95 configuration, and 618.2 MPa and 2.918 cm for the thick-wall L-80 configuration. The combined 9.625-in casing and 7-in liner exhibited the lowest reported response, with a maximum von Mises stress of 78.6 MPa and a displacement of 0.694 cm in the same section. The standalone 7-in casing showed a less favorable response than the combined configuration. These results indicate that, within the modeled conditions, increasing wall thickness and incorporating an inner liner may reduce predicted stress and displacement more substantially than upgrading steel grade alone. The findings are specific to a single-well static numerical assessment and require further numerical verification and independent field validation. Because time-dependent salt creep was not explicitly modeled, the results do not establish long-term casing performance.

Authors

Institutions

Publication Details

Journal
Scientific Reports
Published
2026-11-13
DOI
https://doi.org/10.1038/s41598-026-80030-1
Primary Topic
Drilling and Well Engineering
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Integrated mechanical earth modeling and finite-element assessment of casing-collapse mitigation strategies in high-stress salt-bearing caprocks

Erfan Hosseini, Behzad Elahifar
1 links
Scientific Reports
Drilling and Well Engineering
article

Integrated mechanical earth modeling and finite-element assessment of casing-collapse mitigation strategies in high-stress salt-bearing caprocks

Erfan Hosseini, Behzad Elahifar
article en

Abstract

Casing collapse in wells penetrating salt-bearing caprocks is a significant well-integrity concern because anisotropic in-situ stresses and mechanical contrasts between geological formations can produce non-uniform loading. This study integrates a Mechanical Earth Model (MEM) with finite-element analysis (FEA) to evaluate the mechanical response of alternative casing configurations in a deep well. Acoustic and density logs from 3050 to 3618 m were used to estimate formation elastic properties and in-situ stresses. These estimates were applied to models of the formation–cement–casing system. The baseline 9.625-in production casing was compared with four alternatives: a thicker-wall T-95 casing configuration, a thick-wall L-80 casing, a 7-in inner liner installed within the existing casing, and a standalone 7-in casing. The predicted maximum von Mises stress and radial displacement were used as the primary response indicators. The baseline configuration produced a maximum von Mises stress of 1010.2 MPa and a displacement of 4.574 cm in Gachsaran Section 2. The corresponding values were 871.4 MPa and 3.821 cm for the T-95 configuration, and 618.2 MPa and 2.918 cm for the thick-wall L-80 configuration. The combined 9.625-in casing and 7-in liner exhibited the lowest reported response, with a maximum von Mises stress of 78.6 MPa and a displacement of 0.694 cm in the same section. The standalone 7-in casing showed a less favorable response than the combined configuration. These results indicate that, within the modeled conditions, increasing wall thickness and incorporating an inner liner may reduce predicted stress and displacement more substantially than upgrading steel grade alone. The findings are specific to a single-well static numerical assessment and require further numerical verification and independent field validation. Because time-dependent salt creep was not explicitly modeled, the results do not establish long-term casing performance.

Scientific Reports
National Iranian Oil Company (Iran) (IR), Norwegian University of Science and Technology (NO)
Drilling and Well Engineering
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon