Effect of Laser Remelting on the Microstructure, Mechanical and Tribological Properties of Detonation-Sprayed NiCrFeBSiC Coatings for Mechanical Engineering Applications

This study investigates the effect of laser remelting on the microstructure, phase composition, mechanical properties, tribological behavior, and corrosion resistance of self-fluxing NiCrFeBSiC coatings deposited onto AISI 321 stainless steel by detonation spraying. The coatings were characterized before and after laser treatment using scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), instrumented indentation, adhesion testing, ball-on-disk tribometry, and potentiodynamic polarization measurements. SEM analysis revealed that laser remelting reduced coating porosity from 0.306 ± 0.014% to 0.15 ± 0.09%, accompanied by microstructural densification and a reduction in coating thickness. XRD analysis confirmed the preservation of the principal crystalline phases, including Ni3Fe, Cr7C3, CrB, and Ni3B, following laser treatment. The Vickers hardness increased from 1049.1 ± 43.4 to 1206.1 ± 63.1 HV, while the elastic modulus increased from 233.6 ± 6.2 to 258.4 ± 5.3 GPa. Furthermore, adhesion strength increased by 19.4%, whereas surface roughness decreased by 19.2%. Laser remelting significantly improved tribological performance, reducing the average coefficient of friction from 0.535 ± 0.048 to 0.409 ± 0.086 and the specific wear rate from 2.864 × 10−4 to 1.447 × 10−4 mm3/(N·m), corresponding to a 49.5% reduction in wear. Electrochemical measurements indicated a modest decrease in corrosion current density of approximately 3.0%, accompanied by changes in the morphology of corrosion-affected regions. The improvements are associated with laser-induced microstructural densification, redistribution of alloying elements, and preservation of hard reinforcing phases. These findings demonstrate the potential of combining detonation spraying with laser remelting to produce wear-resistant nickel-based protective coatings for mechanical and power engineering applications.

Authors

Institutions

Publication Details

Journal
Journal of Manufacturing and Materials Processing
Published
2026-11-13
DOI
https://doi.org/10.3390/jmmp10110508
Primary Topic
Surface Treatment and Coatings
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Effect of Laser Remelting on the Microstructure, Mechanical and Tribological Properties of Detonation-Sprayed NiCrFeBSiC Coatings for Mechanical Engineering Applications

A.Y. Zhakupova, Daryn Baizhan, Dastan Buitkenov, Laila Sulyubayeva et al.
1 links
Journal of Manufacturing and Materials Processing
Surface Treatment and Coatings
article

Effect of Laser Remelting on the Microstructure, Mechanical and Tribological Properties of Detonation-Sprayed NiCrFeBSiC Coatings for Mechanical Engineering Applications

A.Y. Zhakupova, Daryn Baizhan, Dastan Buitkenov, Laila Sulyubayeva, Nurmakhanbet Raisov, Nurbol Berdimuratov
article en

Abstract

This study investigates the effect of laser remelting on the microstructure, phase composition, mechanical properties, tribological behavior, and corrosion resistance of self-fluxing NiCrFeBSiC coatings deposited onto AISI 321 stainless steel by detonation spraying. The coatings were characterized before and after laser treatment using scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), instrumented indentation, adhesion testing, ball-on-disk tribometry, and potentiodynamic polarization measurements. SEM analysis revealed that laser remelting reduced coating porosity from 0.306 ± 0.014% to 0.15 ± 0.09%, accompanied by microstructural densification and a reduction in coating thickness. XRD analysis confirmed the preservation of the principal crystalline phases, including Ni3Fe, Cr7C3, CrB, and Ni3B, following laser treatment. The Vickers hardness increased from 1049.1 ± 43.4 to 1206.1 ± 63.1 HV, while the elastic modulus increased from 233.6 ± 6.2 to 258.4 ± 5.3 GPa. Furthermore, adhesion strength increased by 19.4%, whereas surface roughness decreased by 19.2%. Laser remelting significantly improved tribological performance, reducing the average coefficient of friction from 0.535 ± 0.048 to 0.409 ± 0.086 and the specific wear rate from 2.864 × 10−4 to 1.447 × 10−4 mm3/(N·m), corresponding to a 49.5% reduction in wear. Electrochemical measurements indicated a modest decrease in corrosion current density of approximately 3.0%, accompanied by changes in the morphology of corrosion-affected regions. The improvements are associated with laser-induced microstructural densification, redistribution of alloying elements, and preservation of hard reinforcing phases. These findings demonstrate the potential of combining detonation spraying with laser remelting to produce wear-resistant nickel-based protective coatings for mechanical and power engineering applications.

Journal of Manufacturing and Materials ProcessingVol. 10(11)
L. N. Gumilyov Eurasian National University (KZ), Sarsen Amanzholov East Kazakhstan University (KZ)
Surface Treatment and Coatings
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon