Experimental Evaluation of the Influence of Titanium Alloy Bars on the Seismic Performance of Cast-in-Place Normal Concrete and Ultrahigh-Performance Concrete Bridge Piers

Abstract Traditional reinforced concrete (RC) bridges are known to be susceptible to corrosion from diverse environmental factors such as salts, chlorides, carbonation, and humidity. This deterioration, if not adequately corrected, can compromise the intended service life and/or safety of existing bridges. For this reason, recent research has focused on applying advanced composite materials to RC bridges to improve their durability. This paper experimentally evaluates the cyclic behavior and seismic performance of titanium alloy bar–reinforced ultrahigh-performance concrete (TARUHPC) bridge piers. This construction technology, which uses titanium alloy bars (TiABs) in place of traditional steel bars for reinforcing ultrahigh-performance concrete (UHPC), aims to increase the durability of RC bridges in seismic regions. Different large-scale bridge piers were tested under cyclic loads to evaluate their failure modes and deformation capacity. A total of four specimens with different material combinations were tested: (1) normal concrete with normal steel, (2) normal concrete with TiABs (NC-TI), (3) UHPC with conventional steel, and (4) UHPC with TiABs (U-TI). All specimens were subjected to a constant axial load, and quasi-static, displacement-controlled loads were applied until failure or significant strength degradation was noted. It was noted that the addition of TiABs significantly reduced the residual deformation in bridge piers with both normal concrete and UHPC. Nevertheless, the use of normal concrete limited the yielding of TiABs for the pier NC-TI, owing to the limited concrete compression capacity. Moreover, the addition of UHPC reduced the cracking and overall damage at the bottom section of piers, thus increasing the deformation capacity. However, it was noted that the foundation should also be cast with UHPC to avoid local damage at the pier–foundation interface. From all the specimens, U-TI (TARUHPC) showed the largest strength and deformation capacity (ductility at failure of above 15.0) with low residual deformations; however, it showed lower damping than Specimen U-NS, which was attributed to the fact that TiABs incurred in less limited deformations.

Authors

Institutions

Publication Details

Journal
Journal of Bridge Engineering
Published
2026-11-12
DOI
https://doi.org/10.1061/jbenf2.beeng-8228
Primary Topic
Structural Behavior of Reinforced Concrete
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Experimental Evaluation of the Influence of Titanium Alloy Bars on the Seismic Performance of Cast-in-Place Normal Concrete and Ultrahigh-Performance Concrete Bridge Piers

Mustafa Mashal, Mahesh Acharya, Luis Alberto Bedriñana, Heider Mendoza Portillo
Journal of Bridge Engineering
Structural Behavior of Reinforced Concrete
article

Experimental Evaluation of the Influence of Titanium Alloy Bars on the Seismic Performance of Cast-in-Place Normal Concrete and Ultrahigh-Performance Concrete Bridge Piers

Mustafa Mashal, Mahesh Acharya, Luis Alberto Bedriñana, Heider Mendoza Portillo
article en

Abstract

Abstract Traditional reinforced concrete (RC) bridges are known to be susceptible to corrosion from diverse environmental factors such as salts, chlorides, carbonation, and humidity. This deterioration, if not adequately corrected, can compromise the intended service life and/or safety of existing bridges. For this reason, recent research has focused on applying advanced composite materials to RC bridges to improve their durability. This paper experimentally evaluates the cyclic behavior and seismic performance of titanium alloy bar–reinforced ultrahigh-performance concrete (TARUHPC) bridge piers. This construction technology, which uses titanium alloy bars (TiABs) in place of traditional steel bars for reinforcing ultrahigh-performance concrete (UHPC), aims to increase the durability of RC bridges in seismic regions. Different large-scale bridge piers were tested under cyclic loads to evaluate their failure modes and deformation capacity. A total of four specimens with different material combinations were tested: (1) normal concrete with normal steel, (2) normal concrete with TiABs (NC-TI), (3) UHPC with conventional steel, and (4) UHPC with TiABs (U-TI). All specimens were subjected to a constant axial load, and quasi-static, displacement-controlled loads were applied until failure or significant strength degradation was noted. It was noted that the addition of TiABs significantly reduced the residual deformation in bridge piers with both normal concrete and UHPC. Nevertheless, the use of normal concrete limited the yielding of TiABs for the pier NC-TI, owing to the limited concrete compression capacity. Moreover, the addition of UHPC reduced the cracking and overall damage at the bottom section of piers, thus increasing the deformation capacity. However, it was noted that the foundation should also be cast with UHPC to avoid local damage at the pier–foundation interface. From all the specimens, U-TI (TARUHPC) showed the largest strength and deformation capacity (ductility at failure of above 15.0) with low residual deformations; however, it showed lower damping than Specimen U-NS, which was attributed to the fact that TiABs incurred in less limited deformations.

Journal of Bridge EngineeringVol. 32(1)
Idaho State University (US), Idaho National Laboratory (US), Universidad de Ingeniería y Tecnología (PE)
Industry, innovation and infrastructure, Sustainable cities and communities
Structural Behavior of Reinforced Concrete
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon