Effects of L4-L5 fusion on the adjacent levels in the lumbar spine

Spondylolisthesis and degenerative disc disease can, in some cases, be treated using lumbar fusion techniques; however, the effects of these procedures on the surgical site, adjacent vertebral bodies, and intervertebral discs are not fully understood. In this work, a three-dimensional finite element model of the L1-L5 lumbar spine was developed using Computed Tomography data from a healthy individual, to evaluate stress redistribution following L4-L5 fusion. Four models were evaluated: a healthy spine without instrumentation; a spine with pedicle screw fixation at L4-L5; a spine with pedicle screw fixation and interbody cages at L4-L5; and a spine with interbody fusion at L4-L5. The analysis considered three loading conditions: axial compression, flexion, and extension. Percentage changes in vertebrae cortical-bone and intervertebral lumbar disc stress were calculated relative to the healthy-spine value under the same loading condition. Average von Mises stresses in the L1-L3 cortical bone and the L1-L2 and L2-L3 intervertebral discs remained similar to the healthy spine. Fusion reduced stress in the L4 vertebra relative to the screw-only construct, whereas L5 cortical bone stress increased across all instrumented configurations. Screw only fixation produced the largest increases, while the fused screw and cage construct produced the smallest, demonstrating that construct design and fusion state influence load redistribution at the fused level. The superior adjacent L3-L4 disc experienced a consistent 34-42% increase in stress across all instrumented models, indicating elevated adjacent segment loading even when cage-based constructs reduced stresses at L5. Flexion generated the highest stresses, approximately 90% greater than extension and 35% greater than compression, highlighting the sensitivity of postoperative load sharing to loading direction. These findings show that L4-L5 fusion alters stress distribution within the fused segment and the superior adjacent level, providing comparative biomechanical insight into how construct design and loading conditions influence postoperative load transfer. .

Authors

Institutions

Publication Details

Journal
Biomedical Physics & Engineering Express
Published
2026-11-12
DOI
https://doi.org/10.1088/2057-1976/aec171
Primary Topic
Spine and Intervertebral Disc Pathology
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Effects of L4-L5 fusion on the adjacent levels in the lumbar spine

Gurpreet Singh, Teresa A Alonso-Rasgado, F. M. Martinez-Lozada, Rajat Verma et al.
Biomedical Physics & Engineering Express
Spine and Intervertebral Disc Pathology
article

Effects of L4-L5 fusion on the adjacent levels in the lumbar spine

Gurpreet Singh, Teresa A Alonso-Rasgado, F. M. Martinez-Lozada, Rajat Verma, Colin G. Bailey, Saeed Mohammad
article en

Abstract

Spondylolisthesis and degenerative disc disease can, in some cases, be treated using lumbar fusion techniques; however, the effects of these procedures on the surgical site, adjacent vertebral bodies, and intervertebral discs are not fully understood. In this work, a three-dimensional finite element model of the L1-L5 lumbar spine was developed using Computed Tomography data from a healthy individual, to evaluate stress redistribution following L4-L5 fusion. Four models were evaluated: a healthy spine without instrumentation; a spine with pedicle screw fixation at L4-L5; a spine with pedicle screw fixation and interbody cages at L4-L5; and a spine with interbody fusion at L4-L5. The analysis considered three loading conditions: axial compression, flexion, and extension. Percentage changes in vertebrae cortical-bone and intervertebral lumbar disc stress were calculated relative to the healthy-spine value under the same loading condition. Average von Mises stresses in the L1-L3 cortical bone and the L1-L2 and L2-L3 intervertebral discs remained similar to the healthy spine. Fusion reduced stress in the L4 vertebra relative to the screw-only construct, whereas L5 cortical bone stress increased across all instrumented configurations. Screw only fixation produced the largest increases, while the fused screw and cage construct produced the smallest, demonstrating that construct design and fusion state influence load redistribution at the fused level. The superior adjacent L3-L4 disc experienced a consistent 34-42% increase in stress across all instrumented models, indicating elevated adjacent segment loading even when cage-based constructs reduced stresses at L5. Flexion generated the highest stresses, approximately 90% greater than extension and 35% greater than compression, highlighting the sensitivity of postoperative load sharing to loading direction. These findings show that L4-L5 fusion alters stress distribution within the fused segment and the superior adjacent level, providing comparative biomechanical insight into how construct design and loading conditions influence postoperative load transfer. .

Biomedical Physics & Engineering Express
Queen Mary University of London (GB), University of Manchester (GB)
Good health and well-being
Spine and Intervertebral Disc Pathology
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon