Efficiency of photocatalytic ozonation process in the presence of CoFe₂O₄/ZnTiO₃/Ag nanocomposite for the removal of bisphenol a from aqueous solutions

Bisphenol A (BPA), a ubiquitous endocrine-disrupting compound, persists in aquatic environments and resists conventional wastewater treatment, posing ecological and human health risks. In this study, a magnetic CoFe₂O₄/ZnTiO₃/Ag ternary nanocomposite was prepared by co-precipitation and calcination and tested as a heterogeneous catalyst for BPA removal by photocatalytic ozonation (6 W UV-C lamp, 0.2 g/h ozone) in a model aqueous system. XRD showed reflections of a spinel phase and metallic silver together with weak reflections attributed to ilmenite-type ZnTiO₃; however, the iron-rich EDX composition and an XRD pattern of the calcined core that includes reflections consistent with hematite show that the material is not phase-pure. Batch experiments (one run per condition) varied initial BPA concentration (10–50 mg/L), catalyst dosage (0.25–0.75 g/L), pH (4–10) and reaction time (up to 240 min). Under the best conditions tested (pH 7, 0.5 g/L catalyst, 10 mg/L BPA), BPA removal reached 91.30% and COD removal 82.5% after 240 min. Under the same conditions, removal was 76.09% for UV-C/O₃, 70.65% for O₃ alone, 9.78% for UV-C alone and 1.09% for the catalyst alone. The catalyst with UV-C but without ozone removed 85.87%, and the catalyst with ozone but without light removed 80.43%, so the composite acted both as a photocatalyst and as an ozonation catalyst. A 400 W metal halide lamp used as a simulated-sunlight source gave no improvement over the catalyst/O₃ system (80.65% versus 80.43%). The apparent rate constant of the three-component process was about 1.8 times the sum of those of the single processes but only about 1.25 times that of the best two-component process (catalyst/UV-C). Removal fell from 91.30% to 47.83% over seven reuse cycles, while the catalyst was easily recovered with a magnet. The proposed mechanism and degradation pathway are hypotheses based on the literature and on tentatively identified intermediates and were not tested directly. The results suggest that the system is a promising option for BPA removal in model water; regeneration, metal leaching, toxicity of the treated water and performance in real wastewater remain to be studied.

Authors

Institutions

Publication Details

Journal
Scientific Reports
Published
2026-11-13
DOI
https://doi.org/10.1038/s41598-026-79903-2
Primary Topic
Advanced oxidation water treatment
Type
article
Field-Weighted Citation Impact
0.00

Funders

Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Efficiency of photocatalytic ozonation process in the presence of CoFe₂O₄/ZnTiO₃/Ag nanocomposite for the removal of bisphenol a from aqueous solutions

Ali Sobhani‐Nasab, Akram Yazdani, Omid Hatami, Rouhullah Dehghani et al.
3 links
Scientific Reports
Advanced oxidation water treatment
article

Efficiency of photocatalytic ozonation process in the presence of CoFe₂O₄/ZnTiO₃/Ag nanocomposite for the removal of bisphenol a from aqueous solutions

Ali Sobhani‐Nasab, Akram Yazdani, Omid Hatami, Rouhullah Dehghani, Hasan Rahmani
article en

Abstract

Bisphenol A (BPA), a ubiquitous endocrine-disrupting compound, persists in aquatic environments and resists conventional wastewater treatment, posing ecological and human health risks. In this study, a magnetic CoFe₂O₄/ZnTiO₃/Ag ternary nanocomposite was prepared by co-precipitation and calcination and tested as a heterogeneous catalyst for BPA removal by photocatalytic ozonation (6 W UV-C lamp, 0.2 g/h ozone) in a model aqueous system. XRD showed reflections of a spinel phase and metallic silver together with weak reflections attributed to ilmenite-type ZnTiO₃; however, the iron-rich EDX composition and an XRD pattern of the calcined core that includes reflections consistent with hematite show that the material is not phase-pure. Batch experiments (one run per condition) varied initial BPA concentration (10–50 mg/L), catalyst dosage (0.25–0.75 g/L), pH (4–10) and reaction time (up to 240 min). Under the best conditions tested (pH 7, 0.5 g/L catalyst, 10 mg/L BPA), BPA removal reached 91.30% and COD removal 82.5% after 240 min. Under the same conditions, removal was 76.09% for UV-C/O₃, 70.65% for O₃ alone, 9.78% for UV-C alone and 1.09% for the catalyst alone. The catalyst with UV-C but without ozone removed 85.87%, and the catalyst with ozone but without light removed 80.43%, so the composite acted both as a photocatalyst and as an ozonation catalyst. A 400 W metal halide lamp used as a simulated-sunlight source gave no improvement over the catalyst/O₃ system (80.65% versus 80.43%). The apparent rate constant of the three-component process was about 1.8 times the sum of those of the single processes but only about 1.25 times that of the best two-component process (catalyst/UV-C). Removal fell from 91.30% to 47.83% over seven reuse cycles, while the catalyst was easily recovered with a magnet. The proposed mechanism and degradation pathway are hypotheses based on the literature and on tentatively identified intermediates and were not tested directly. The results suggest that the system is a promising option for BPA removal in model water; regeneration, metal leaching, toxicity of the treated water and performance in real wastewater remain to be studied.

Scientific Reports
Kashan University of Medical Sciences (IR)
Kashan University of Medical Sciences
Clean water and sanitation, Responsible consumption and production
Advanced oxidation water treatment
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon