Utilization of Induction-Furnace Slag as a Partial Silica Sand Replacement in CO2–Sodium Silicate Molding: Effects on Mold Properties and Casting Quality

Landfill disposal of induction-furnace slag is a recurring cost for steel foundries, while rising silica sand costs burden CO 2 -sodium silicate molding. This study evaluates induction-furnace slag from AISI/SAE 4130 low-alloy steel melting as a partial silica sand replacement in CO 2 -hardened sodium silicate molds. Slag was substituted at six levels (10–40 wt.%) using cylindrical specimens rammed and CO 2 -gassed per AFS practice (triplicate, n = 3). Permeability, shatter index, green compression strength, green shear strength and mold hardness were measured, with all levels validated by casting trials at 1600°C. All five properties decreased monotonically with slag content, falling by 27.7–46.2% between the 0% (pure sand) baseline and 40% slag. EDS and sieve analysis identified two independent bases for this decline, slag is chemically lower in silicon and enriched in iron, manganese, calcium, chromium and molybdenum and also substantially finer and richer in fines than the base sand. Within the tested range, 25–30% slag gave the best balance of property retention and substitution level, remaining workable for small-to-medium steel castings. Trial castings showed no visible surface defects across all seven conditions, with surface roughness remaining within a comparatively narrow band and no consistent worsening trend with slag content. Partial slag substitution also reduces raw-material cost versus an all-silica-sand mold. These results support induction-furnace slag as a viable, low-cost partial substitute for silica sand in CO 2 molding, with 25–30% identified as a practical substitution window for industrial by product valorization.

Authors

Institutions

Publication Details

Journal
International Journal of Metalcasting
Published
2026-11-21
DOI
https://doi.org/10.1007/s40962-026-02199-5
Primary Topic
Materials Engineering and Processing
Type
article
Field-Weighted Citation Impact
0.00
Controls
|||
ALL TIME
JAN
FEB
MAR
APR
MAY
JUN
JUL
AUG
SEP
OCT
NOV
article

Utilization of Induction-Furnace Slag as a Partial Silica Sand Replacement in CO2–Sodium Silicate Molding: Effects on Mold Properties and Casting Quality

Suresh T., Yuvaraja Jayamoorthi, Govindarasu Periyasamy, Samuel Rathna Kumar P S
1 links
International Journal of Metalcasting
Materials Engineering and Processing
article

Utilization of Induction-Furnace Slag as a Partial Silica Sand Replacement in CO2–Sodium Silicate Molding: Effects on Mold Properties and Casting Quality

Suresh T., Yuvaraja Jayamoorthi, Govindarasu Periyasamy, Samuel Rathna Kumar P S
article en

Abstract

Landfill disposal of induction-furnace slag is a recurring cost for steel foundries, while rising silica sand costs burden CO 2 -sodium silicate molding. This study evaluates induction-furnace slag from AISI/SAE 4130 low-alloy steel melting as a partial silica sand replacement in CO 2 -hardened sodium silicate molds. Slag was substituted at six levels (10–40 wt.%) using cylindrical specimens rammed and CO 2 -gassed per AFS practice (triplicate, n = 3). Permeability, shatter index, green compression strength, green shear strength and mold hardness were measured, with all levels validated by casting trials at 1600°C. All five properties decreased monotonically with slag content, falling by 27.7–46.2% between the 0% (pure sand) baseline and 40% slag. EDS and sieve analysis identified two independent bases for this decline, slag is chemically lower in silicon and enriched in iron, manganese, calcium, chromium and molybdenum and also substantially finer and richer in fines than the base sand. Within the tested range, 25–30% slag gave the best balance of property retention and substitution level, remaining workable for small-to-medium steel castings. Trial castings showed no visible surface defects across all seven conditions, with surface roughness remaining within a comparatively narrow band and no consistent worsening trend with slag content. Partial slag substitution also reduces raw-material cost versus an all-silica-sand mold. These results support induction-furnace slag as a viable, low-cost partial substitute for silica sand in CO 2 molding, with 25–30% identified as a practical substitution window for industrial by product valorization.

International Journal of Metalcasting
Karpagam Academy of Higher Education (IN), Kumaraguru College of Technology (IN)
Responsible consumption and production, Industry, innovation and infrastructure
Materials Engineering and Processing
AI Navigator

Ask Laika to Summarize, Analyze, and Connect papers live on the map.

Summarize Papers & Methodologies

Extract key findings, datasets, and comparative methods across publications.

Benchmark Rankings & Visual Analytics

Rank top research institutions, authors, funders, topics, and journals by Field-Weighted Citation Impact (FWCI) and paper volume with instant charts.

Connect Distant Disciplines

Bridge topological clusters on the map to find hidden collaborative intersections.

Laika access coming soon